Rockwell-automation 20P PowerFlex DC Drive - Frame D AC Current Transd Instrukcja Użytkownika Pobierz pdf

Publication 20P-IN059A-EN-P

PowerFlex® DC Drive

Frame D AC Current Transducers

Installation Instructions

What This Kit Includes

• Two AC current transducers

• Four mounting screws

• Static strap

Tools That You Need

• Hexalobular screwdriver

• Flathead screwdriver

• Torque wrench

What You Need to Do

To install the AC current transducers:

❐ Step 1: Remove power from the drive

❐ Step 2: Remove the protective covers and open the control panel

❐ Step 3: Remove the existing AC current transducers

❐ Step 4: Install the new AC current transducers

❐ Step 5: Close the control panel, replace the covers and document the

change

ATTENTION: Only qualified personnel familiar with DC drives

and associated machinery should plan or implement the installation,

start-up and subsequent maintenance of the system. Failure to comply

may result in personal injury and/or equipment damage.

ATTENTION: To avoid an electric shock hazard, ensure that all

power to the drive has been removed before performing the following.

ATTENTION: This drive contains ESD (Electrostatic Discharge)

sensitive parts and assemblies. Static control precautions are required

when installing, testing, servicing or repairing this assembly.

Component damage may result if ESD control procedures are not

followed. If you are not familiar with static control procedures,

reference A-B publication 8000-4.5.2, “Guarding Against

Electrostatic Damage” or any other applicable ESD protection

handbook.

1 2 3 4 5 6 7 8

Podsumowanie treści

Strona 1 - Installation Instructions

Publication 20P-IN059A-EN-PPowerFlex® DC DriveFrame D AC Current TransducersInstallation InstructionsWhat This Kit Includes• Two AC current transducer

Strona 2 - Protective Covers and Open

Publication 20P-IN059A-EN-P2Step 1: Remove Power from the Drive• Remove and lock-out all incoming power to the drive. Step 2: Remove the Protective Co

Strona 3 - 1.5 N•m (13 lb•in)

3Publication 20P-IN059A-EN-P2. Loosen, but do not remove, the six hexalobular screws that secure the top air flow plate to the drive, then slide the p

Strona 4 - Existing AC Current

Publication 20P-IN059A-EN-P4Step 3: Remove the Existing AC Current TransducersImportant: Mark all connections and wires before removal to avoid incorr

Strona 5 - Publication 20P-IN059A-EN-P

5Publication 20P-IN059A-EN-P3. Remove the bolt and washer that secures each of the U and W phase AC input terminal bus bars to the rear insulator bar.

Strona 6 - Current Transducers

Publication 20P-IN059A-EN-P66. Remove the four M12 bolts and washers that secure each of the U and W phase AC input terminal bus bars to the input bus

Strona 7 - Related Documentation

7Publication 20P-IN059A-EN-PStep 5: Close the Control Panel, Replace the Covers and Document the Change1. Close the control panel and replace the top

Strona 8

Komentarze do niniejszej Instrukcji

Brak uwag

Rockwell-automation 20P PowerFlex DC Drive - Frame D AC Current Transd Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Ekwipunek Rockwell-automation 20P PowerFlex DC Drive - Frame D AC Current Transd. Rockwell Automation 20P PowerFlex DC Drive - Frame D AC Current Transducers User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 20P PowerFlex DC Drive - Frame D AC Current Transd