Rockwell-automation 900 Temperature Controller Communications Function Instrukcja Użytkownika Pobierz pdf (Strona 52)

Publication 900-UM004D-EN-E - July 2010

3-10 Communications Data

C3 (83) 004E Control output 1

assignment

When control output 1 is a linear output:

H’00000000 (0): Not assigned.

H’00000001 (1): Control output (heating)

H’00000002 (2): Control output (cooling)

When control output 1 is an ON/OFF pulse output:

H’00000000 (0): Not assigned.

H’00000001 (1): Control output (heating)

H’00000002 (2): Control output (cooling)

H’00000003 (3): Alarm 1

H’00000004 (4): Alarm 2

H’00000005 (5): Alarm 3

H’00000006 (6): Program end output➒

H’00000007 (7): Control output ON/OFF count alarm ➓

Advanced

function

setting

C3 (83) 004F Control output 2

assignment

H’00000000 (0): Not assigned.

H’00000001 (1): Control output (heating)

H’00000002 (2): Control output (cooling)

H’00000003 (3): Alarm 1

H’00000004 (4): Alarm 2

H’00000005 (5): Alarm 3

H’00000006 (6): Program end output➒)

H’00000007 (7): Control output ON/OFF count alarm ➓

C3 (83) 0050 Auxiliary Output 1

assignment

H’00000000 (0): Not assigned.

H’00000001 (1): Control output (heating)

H’00000002 (2): Control output (cooling)

H’00000003 (3): Alarm 1

H’00000004 (4): Alarm 2

H’00000005 (5): Alarm 3

H’00000006 (6): Program end output➒)

H’00000007 (7): Control output ON/OFF count alarm ➓

C3 (83) 0051 Auxiliary Output 2

assignment

H’00000000…H’0000000F (0…15)

* Same settings as Auxiliary Output 1 assignments

C3 (83) 0052 Character select H’00000000 (0): OFF

H’00000001 (1): ON

C3 (83) 0053 Program pattern H’00000000 (0): OFF

H’00000001 (1): STOP

H’00000002 (2): CONT

Initial

setting

Table 3.3 Variable Type C3 (83)

Variable

Typ e

Address Item (Parameter) Set (Monitor) Value Function

Group

➊ The input type can be selected to march the connected sensor. There are two input types specifications:

Thermocouple/Resistance thermometer input and Analog input.

➋ The parameter will not be shown on the Controller display when alarm 3 is not assigned to an output.

➌ Communications parameters are enabled after they have been changed by resetting the controller.

➍ For controllers with two event inputs (events 1 and 2), this cannot be set if the number of Multi-SP uses parameter is set to 1

or 2

➎ For controllers with two event inputs (events 1 and 2), this cannot be set if the number of Multi-SP uses parameter is set to 2.

➏ PRST (program start) can be set even when the program pattern is set to OFF, but the function will be disabled.

➐ The logic of CompoWay/F (900-TC) operation command code 00 (communications writing) is not affected.

➑ The setting (monitor) range depends on the transfer output type setting. (See the setting data list for details.)

➒ P.END (program end output) can be set even when the program pattern is set to OFF, but the

function will be disabled.

➓ The output turns ON when the status of either the Control Output 1 ON/OFF Count Alarm or the Control Output 2 ON/OFF

Count Alarm turns ON.

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 102 103

Komentarze do niniejszej Instrukcji

Brak uwag

Rockwell-automation 900 Temperature Controller Communications Function Instrukcja Użytkownika Strona 52

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 900 Temperature Controller Communications Function