Rockwell-automation 20-COMM-M Modbus/TCP Adapter Instrukcja Użytkownika Strona 80
- Strona / 98
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
B-4 Adapter Parameters
20-COMM-M Modbus/TCP Adapter User Manual
Publication 20COMM-UM014C-EN-P
24 [DPI I/O Cfg]
Sets the I/O that is transferred through the adapter.
Default: xxx0 0001
Bit Values: 0 = I/O disabled
1 = I/O enabled
Type: Read/Write
Reset Required: Yes
25 [DPI I/O Act]
Displays the I/O that the adapter is actively
transmitting. The value of this parameter will usually be
equal to the value of Parameter 24 - [DPI I/O Cfg].
Default: xxx0 0001
Bit Values: 0 = I/O disabled
1 = I/O enabled
Type: Read Only
26 [Flt Cfg Logic]
Sets the Logic Command data that is sent to the drive
if Parameter 23 - [Comm Flt Action] is set to “4”
(Send Flt Cfg) and communications are disrupted.
The bit definitions will depend on the product to which
the adapter is connected. See Appendix C or the
documentation for the drive being used.
Default: 0000 0000 0000 0000
Minimum: 0000 0000 0000 0000
Maximum: 1111 1111 1111 1111
Type: Read/Write
Reset Required: No
27 [Flt Cfg Ref]
Sets the Reference data that is sent to the drive if
Parameter 23 - [Comm Flt Action] is set to “4” (Send
Flt Cfg) and communications are disrupted.
Default: 0
Minimum: 0
Maximum: 4294967295
Type: Read/Write
Reset Required: No
Important: If the drive uses a 16-bit
Reference, the most significant word of
this value must be set to zero (0) or a
fault will occur.
28
29
30
31
32
33
34
35
[Flt Cfg A1 In]
[Flt Cfg A2 In]
[Flt Cfg B1 In]
[Flt Cfg B2 In]
[Flt Cfg C1 In]
[Flt Cfg C2 In]
[Flt Cfg D1 In]
[Flt Cfg D2 In]
Sets the data that is sent to the Datalink in the drive if
Parameter 23 - [Comm Flt Action] is set to “4” (Send
Flt Cfg) and communications are disrupted.
Default: 0
Default: 0
Default: 0
Default: 0
Default: 0
Default: 0
Default: 0
Default: 0
Minimum: 0
Maximum: 4294967295
Type: Read/Write
Reset Required: No
Important: If the drive uses 16-bit
Datalinks, the most significant word of
this value must be set to zero (0) or a
fault will occur.
36 [Web Enable]
Displays the setting of the adapter Web Pages Switch
(SW2 in Figure 2.1
) when the adapter was last reset.
Default: 0 = Disabled
Values: 0 = Disabled
1 = Enabled
Type: Read Only
Parameter
No. Name and Description Details
Bit
Definition
Not Used
Not Used
Not Used
Datalink D
Datalink C
Datalink B
Datalink A
Cmd/Ref
Default x x x 0 0 0 0 1
Bit 76543210
Bit
Definition
Not Used
Not Used
Not Used
Datalink D
Datalink C
Datalink B
Datalink A
Cmd/Ref
Default x x x 0 0 0 0 1
Bit 76543210
- 20-COMM-M Modbus/TCP Adapter 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- About This Manual 7
- Rockwell Automation 8
- Conventions Used in This 8
- Getting Started 9
- Features 10
- Compatible Products 10
- Required Equipment 11
- Safety Precautions 11
- 1-4 Getting Started 12
- Quick Start 13
- Status Indicators 14
- Installing the Adapter 15
- Setting the Web Pages 16
- Connecting the Adapter to 17
- Applying Power 20
- Commissioning the Adapter 22
- Configuring the Adapter 23
- Using the PowerFlex 7-Class 24
- Using BOOTP 25
- Configuring the Adapter 3-5 27
- Setting the IP Address 28
- Subnet Mask, and Gateway 28
- Setting the Data Rate 30
- Setting the I/O 30
- Configuration 30
- Setting a Communication 31
- Fault Action 31
- Setting the Message I/O 32
- Setting Web Access Control 33
- Resetting the Adapter 34
- Viewing the Adapter Status 34
- Using Parameters 34
- Flash Updating the Adapter 35
- 3-14 Configuring the Adapter 36
- Chapter 4 37
- Unit Identifier (Port Number) 38
- Using the I/O 39
- Par. 82 - [Maximum Speed] 42
- Accessing Device Parameters 45
- Direct Access Method 45
- Indirect Access Method 46
- Using Datalinks 48
- Rules for Using Datalinks 48
- Reading Datalinks 48
- Writing Datalinks 49
- Conversion Example: 50
- Supported Modbus 51
- Registers 51
- Chapter 5 53
- PORT Status Indicator 54
- MOD Status Indicator 54
- NET A Status Indicator 55
- NET B Status Indicator 55
- Viewing Adapter Diagnostic 56
- Viewing and Clearing 58
- Table 5.B Adapter Events 59
- 5-8 Troubleshooting 60
- Chapter 6 61
- Process Display Pop-up 64
- TCP/IP Configuration Web 65
- Configure E-mail 66
- Notification Web Page 66
- DPI Device Information 69
- Kit (20-XCOMM-DC-BASE) 73
- Specifications 75
- Environmental 76
- Regulatory Compliance 76
- Adapter Parameters 77
- B-6 Adapter Parameters 82
- Logic Command/Status Words 83
- Logic Status Word 84
- PowerFlex 700S Drives 85
- Glossary 87
- G-2 Glossary 88
- F Fault Action 89
- G Gateway 89
- H Hardware Address 89
- I I/O Data 90
- L Logic Command/Logic Status 91
- M Modbus/TCP Network 91
- N NVS (Non-Volatile Storage) 91
- R Reference/Feedback 92
- S Status Indicators 92
- Z Zero Data 92
- May, 2010 98
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 20-COMM-M Modbus/TCP Adapter
Ekwipunek Rockwell-automation 140EX-JE2_JE3 Molded Case Circuit Breaker Instrukcja Użytkownika
(2 strony)
(2 strony)
Ekwipunek Rockwell-automation 56AMXN ControlLogix/AutoMax/Communication/Module Instrukcja Użytkownika
(24 strony)
(24 strony)
Ekwipunek Rockwell-automation 57RF RFID ICODE Handheld Interface User Manual Instrukcja Użytkownika
(112 strony)
(112 strony)
Ekwipunek Rockwell-automation 140G_MG- General Warning for Trip Units Instrukcja Użytkownika
(1 strony)
(1 strony)
Ekwipunek Rockwell-automation 22-HIM-C2S PowerFlex 4-Class Remote Small HIM Instrukcja Użytkownika
(4 strony)
(4 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji