Rockwell-automation 283D ArmorStart - Getting Started Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Ekwipunek Rockwell-automation 283D ArmorStart - Getting Started. Rockwell Automation 283D ArmorStart - Getting Started User Manual Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
Przeglądanie stron 0
QUICK START
ARMORSTART
®
DISTRIBUTED
MOTOR CONTROLLER
Getting Started
BULLETIN 283D
Introduction This guide provides the basic information required to start up your
ArmorStart
®
Distributed Motor Controller. Factory default settings
and information regarding installing, programming, and DeviceNet™
Node Commissioning are described here. For detailed information on
specific product features or configurations, refer to the ArmorStart
user manual, publication 283-UM001*-EN-P.
This guide is intended for qualified service personnel responsible for
setting up and servicing these devices. You must have previous
experience with and a basic understanding of electrical terminology,
configuration procedures, required equipment, and safety precautions.
You should understand DeviceNet network operations, including how
slave devices operate on a network and communicate with a
DeviceNet master. You should also be familiar with RSNetWorx™
for DeviceNet. You must use RSNetWorx for DeviceNet Revision
3.21 Service Pack 2 or later. This software package is referred to
often in this manual. Rockwell Automation product EDS files are
available on the internet at: http://www.ab.com/networks/eds
.
Przeglądanie stron 0
1 2 3 4 5 6 ... 23 24

Podsumowanie treści

Strona 1 - MOTOR CONTROLLER

QUICK STARTARMORSTART® DISTRIBUTED MOTOR CONTROLLER Getting StartedBULLETIN 283DIntroduction This guide provides the basic information required to sta

Strona 2 - 2

10 Publication 283D-QS001C-EN-P - July 2006ArmorStart with ArmorConnect ConnectivityInstalling ArmorConnect Power Media using Cord GripsContro

Strona 3 - 3

Publication 283D-QS001C-EN-P - July 2006 11ArmorConnect Cable RatingsThe ArmorConnect Power Media cables are rated per UL Type TC 600V 90 °C Dr

Strona 4 - 4

12 Publication 283D-QS001C-EN-P - July 2006Group Motor Installations for USA and Canada MarketsThe ArmorStart Distributed Motor controllers are

Strona 5 - 5

Publication 283D-QS001C-EN-P - July 2006 13maintenance while energized. In lieu of this service, the ArmorStart is meant to be unplugged and re

Strona 6 - Conduit Entrance

14 Publication 283D-QS001C-EN-P - July 2006LED Status Indication The LED Status Indication provides 4 status LEDs and a Reset button. The LEDs

Strona 7 - Disconnect Handle

Publication 283D-QS001C-EN-P - July 2006 15Node Commissioning using HardwareThe ArmorStart is shipped with the hardware rotary switches set to

Strona 8 - Description

16 Publication 283D-QS001C-EN-P - July 2006Table 3 Default I/O Messaging DataDefault Input and Output (I/O) Assembly FormatsThe I/O assembly fo

Strona 9 - Enclosure

Publication 283D-QS001C-EN-P - July 2006 17Setting the Motor FLAThe product should now be configured and communicating on the network. The last

Strona 10 - 10

18 Publication 283D-QS001C-EN-P - July 2006Quick Reference TroubleshootingThere are four LEDs on the front of the ArmorStart that can provide a

Strona 11 - Three-Phase Power Media

Publication 283D-QS001C-EN-P - July 2006 19Fault LED indications for Bulletin 283D ArmorStart Distributed Motor ControllersTable 8 Controller F

Strona 12 - 12

2 Publication 283D-QS001C-EN-P - July 2006Installation The ArmorStart Distributed Motor Controller is convection cooled. Operating temperature

Strona 13 - 13

20 Publication 283D-QS001C-EN-P - July 2006Bulletin 283 ParametersTable 9 Starter Display and Parameter SettingsTable 10 FLA Setting Ranges and

Strona 14 - 14

Publication 283D-QS001C-EN-P - July 2006 21Figure 11 Bulletin 283 ArmorStartFigure 12 Bulletin 283 ArmorStartLED StatusIndicationMotorConnectio

Strona 15 - Detail A

22 Publication 283D-QS001C-EN-P - July 2006Table 11 DeviceNet Media ➊➊See publication M116-CA001A-EN-P for complete cable selection information

Strona 16

Publication 283D-QS001C-EN-P - July 2006 23Table 12 Sensor Media ➊➊See publication M116-CA001A-EN-P for complete cable selection information.➋R

Strona 17 - Setting the Motor FLA

Publication 283D-QS001C-EN-P — July 2006 41053-384-05 (1)Superecedes Publication 283D-QS001B-EN-P — September 2005 Copyright ©2006 Rockwell Automation

Strona 18 - Troubleshooting

Publication 283D-QS001C-EN-P - July 2006 3Dimensions are shown in millimeters (inches). Dimensions are not intended to be used for manufacturin

Strona 19 - Distributed Motor Controllers

4 Publication 283D-QS001C-EN-P - July 2006Dimensions are shown in millimeters (inches). Dimensions are not intended to be used for manufacturin

Strona 20 - Bulletin 283 Parameters

Publication 283D-QS001C-EN-P - July 2006 5Dimensions are shown in millimeters (inches). Dimensions are not intended to be used for manufacturin

Strona 21 - 21

6 Publication 283D-QS001C-EN-P - July 2006Wiring Power, Control, Safety Monitor Inputs, and Ground Wiring Table 1 provides the power, control,

Strona 22 - Table 11 DeviceNet Media

Publication 283D-QS001C-EN-P - July 2006 7Table 2 Power, Control, Safety Monitor, and Ground Terminal Designations➊ Only available with the Saf

Strona 23 - Table 13 Sealing Caps

8 Publication 283D-QS001C-EN-P - July 2006ArmorConnect Power Media DescriptionThe ArmorStart Power Media offers both three-phase and control po

Strona 24 - Trademark List

Publication 283D-QS001C-EN-P - July 2006 9Figure 7 Control Power Media System Overview➏ Control Power Media Patchcords - PatchCord cable with

Komentarze do niniejszej Instrukcji

Brak uwag