Rockwell-automation 45MLA Controller Installation Instructions Instrukcja Użytkownika Pobierz pdf (Strona 11)

Dip Switch Settings

The following tables describe settings for DIP switch arrays S1 and

S2. Note that changes made to these settings take effect only

after a power cycle.

Table 20: DIP Switch Array S1 Settings on the Main PCB

Table 21: DIP Switch Array S2 Settings for 2-Wire (default)/4-Wire

Communication (on extension PCB)

Function

DIP switch array S1

(0: OFF, 1: ON, X: not relevant)

87654321

Default

00000000

Offset to address: 0 (00 Hex)

XXXX0000

Offset to address: 1 (01 Hex)

XXXX0001

Offset to address: 2 (02 Hex)

XXXX0010

Offset to address: 3 (03 Hex)

XXXX0011

Offset to address: 4 (04 Hex)

XXXX0100

Offset to address: 5 (05 Hex)

XXXX0101

Offset to address: 6 (06 Hex)

XXXX0110

Offset to address: 7 (07 Hex)

XXXX0111

Offset to address: 8 (08 Hex)

XXXX1000

Offset to address: 9 (09 Hex)

XXXX1001

Offset to address: 10 (0A Hex)

XXXX1010

Offset to address: 11 (0B Hex)

XXXX1011

Offset to address: 12 (0C Hex)

XXXX1100

Offset to address: 13 (0D Hex)

XXXX1101

Offset to address: 14 (0E Hex)

XXXX1110

Offset to address: 15 (0F Hex)

XXXX1111

Baud rate 19,200 Baud

XX00XXXX

Baud rate 2,400 Baud

XX01XXXX

Baud rate 9,600 Baud

XX10XXXX

Baud rate 57,600 Baud

XX11XXXX

Reset to default

1XXXXXXX

Function

DIP switch array S2

4321

Default 0100

Terminating resistor (135 )OFF XXX0

Terminating resistor (135 ) ON XXX1

Terminating resistor 4-wire OFF X X 0 0

Terminating resistor 4-wire ON X X 1 1

Rx 2-wire 010X

Rx 4-wire 10XX

Functional Description—CAN Model

Figure 8: CAN Board with Pin Locations, Teach Button

The allocation of pins on the main connector, J2, for use with the

CAN controller model is described below.

Table 22: J2 Pin Listings

Pin Signal Description Remarks

10V DC Power —

2+24V DC Power —

3 Ground Ground —

4 Not connected Not connected —

5 In 2 Trigger and hold See User Manual

6 In 1 Not used Not used

7 Out 2 Light array interrupted 

0V DC = interrupted

24V DC = not interrupted

8Out 1 Overhang

0V DC = overhang

24V DC = no overhang

 Or over-height (special function)

In 2

PNP

NPN

PNP

NPN

D7 LED - Power

CAN

Extension

PCB

D3 LED Out 1

D4 LED Out 2

D8 LED

D10 LED

D6 LED In 2

D5 LED In 1

RJ45 Connector

Emitter

RJ45 Connector

Receiver

D2 LED

D1 LED

In 1

Pot 2

Pot 1

Removable

Spring-Loaded

Connector

Input

Logic

Jumpers

J12

J13

Out 1

Out 2

In 1

In 2

n. c.

Earth.

24 VDC

0 VDC

1 2 ... 6 7 8 9 10 11 12 13 14 15 16

Komentarze do niniejszej Instrukcji

Brak uwag

Rockwell-automation 45MLA Controller Installation Instructions Instrukcja Użytkownika Strona 11

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 45MLA Controller Installation Instructions