UserManualProcessorBoard(For 6180 Industrial Computers)Allen-Bradley

1–2 System FeaturesThe onboard I/O controller provides a real-time clock and CMOSRAM. You can set the time for the clock and set/clear the systemvalu

1–3System FeaturesYou can authorize full or limited access to the system by settingpasswords in the Setup program. There are two levels of passwords:

Chapter 2Processor BoardThis chapter describes components of the processor board and thesystem BIOS which configures system components. Topics includ

2–2 Processor Board1234568791011 12 13 14151617181920212223Item Description Item Description1 2 MB TSOP FLASH (U181) 13 Primary Power Connector (J6M1)

2–3Processor BoardThe front panel connectors on the processor board support:• System Reset• Power LED• Hard Drive Activity LED• System Speaker• CPU Fa

2–4 Processor BoardThere are 2 jumper sets (J1F1 and J7K1) for configuring theprocessor board. The processor board is shipped with the defaultsetting

2–5Processor BoardCPU/System Speed SettingsCPU Frequency(MHz)Host BusFrequency(MHz)JumperJ7K1-CJumperK7K1-DCPU ClockMultiplierJumperJ7K1-B200 66 1-2,

2–6 Processor BoardClear Password (Jumper J7K1-A / Pins 1,2,3)Moving the jumper from pins 1-2 (Password Enabled) to pins 2-3(Password Clear) and then

2–7Processor BoardA lithium battery on the processor board provides power for the RealTime Clock (RTC) and CMOS RAM. This battery has an estimatedlif

2–8 Processor Board4. Lift up on the battery with the tip of your finger and removebattery.!CAUTION: Danger of explosion if lithium battery isincorre

Because of the variety of uses for the products described in thispublication, those responsible for the application and use of thiscontrol equipment m

Chapter 3BIOS Setup ProgramThis chapter tells how to use the Setup program built into the systemBIOS.The Setup program allows you to change the confi

3–2 BIOS Setup ProgramMain Menu Options Sub Menu Options AB Default DescriptionSystem Date Specifies the current date. Select the month from a popup m

3–3BIOS Setup ProgramMain Menu Options DescriptionAB DefaultSub Menu OptionsLanguage Language EnglishSpecifies the language used for text strings and

3–4 BIOS Setup ProgramProcessor Type Pentium (R) Family F1 HelpProcessor Speed 166 MHz ESC BackCache Size 256K Enter SelectPeripheral Configuration Pr

3–5BIOS Setup ProgramAdvanced MenuOptionsDescriptionAB DefaultSub Menu OptionsPeripheralConfigurationSerial Port 2 Address COM2,2F8H,IRQ3Selects the a

3–6 BIOS Setup ProgramAdvanced MenuOptionsSub Menu Options AB Default DescriptionAdvanced PowerManagementDisabledEnables or disables the Advanced Powe

3–7BIOS Setup ProgramUser Password is Disabled F1 HelpAdministrative Password is Disabled ESC BackEnter SelectSet User Password Press Enter  Previous

3–8 BIOS Setup ProgramThe Security screen allows you to restrict access to the Setupprogram by setting passwords for two different access modes:• Admi

Appendix ATechnical DataAddress Range (Decimal) HexSizeDescription960K-131072K 100000-8000000 127.25M Extended Memory944K-959K FE000-FFFFF 8K Boot B

Appendix BProcessor Board ConnectorsCOM 2 PS/2MousePS/2KeyboardParallel Port COM 1Serial Port Connectors (COM1, COM2)1596Pin # Signal Name1 DCD2 Ser

PrefaceWho Should Use this Manual P–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . Purpose of this Manual P–1. . . . . . . . . . . . . . .

Processor Board ConnectorsB–2Parallel Port Connector1131425Pin # Signal Name Pin # Signal Name1 Strobe # 14 Auto Feed #2 Data Bit 0 15 Fault #3 Data B

Processor Board ConnectorsB–3Front PanelI/O ConnectorsSpeaker ConnectorSPKRIRSLEEP PWR HD LED PWR LED FANRST1234Pin #Signal Name Wire Color1SPKR_DATA#

Processor Board ConnectorsB–4SLEEP PWR ConnectorSPKRIRSLEEP PWR HD LED PWR LED FANRST12345Hard Drive LED ConnectorSPKRIRSLEEP PWR HD LED PWR LED FANRS

Processor Board ConnectorsB–5Reset ConnectorSPKRIRSLEEP PWR HD LED PWR LED FANRST12Pin # Signal Name1 Reset#2 GroundFan ConnectorSPKRIRSLEEP PWR HD LE

Appendix CSystem BIOS MessagesThe following beep codes may be heard while the Setup programsaves changes to CMOS RAM.Beeps Indicates: Description1 R

System BIOS MessagesC–2The following table lists the error messages that may occur duringBIOS setup or during the initial power-up sequence (Power On

System BIOS MessagesC–3The following table list the error messages that may occur withdevices installed in the PCI card slots.Message MeaningBad PnP S

AAdvanced Menu, BIOS Setup, 3–4Allen–Bradley, P–3Contacting for Assistance, P–3Auto–ConfigurationIDE, 1–2PCI, 1–2BBatteryDisposal, 2–8Replacing, 2–7Be

IndexI–2LLEDHard Drive Active, B–4Power, B–4MMain Menu, BIOS, 3–2Memory Map, A–1Mouse & Keyboard, Connectors, B–2PParallel Port, Connector, B–2PC

Allen-Bradley, a Rockwell Automation Business, has been helping its customers improveproductivity and quality for more than 90 years. We design, manuf

Table of Contentstoc–ii Configuration Jumpers 2–4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CPU / System Speed Settings 2–5. .

Table of Contentstoc–iii Appendix CBIOS Error Beep Codes C–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bootup Error Messages C–2.

Using this ManualRead this preface to familiarize yourself with the rest of the manual.This preface covers the following topics:• who should us

Using this ManualP–2Chapter Title ContentsPrefaceDescribes the purpose, background, and scope ofthis manual. Also specifies the audience forwhom thi

Using this Manual P–3Allen-Bradley offers support services worldwide, with over 75Sales/Support Offices, 512 authorized Distributors and 260authorize

Chapter 1 This chapter describes features of the processor board used by the6180 Industrial Computer.The onboard I/O controller (Natio