Rockwell-automation MD60 User Manual Version 3.0 Instrukcja Użytkownika Strona 51
- Strona / 136
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Parameter Descriptions 9-1
CHAPTER 9
Parameter Descriptions
The following information is provided for each parameter along with
its description:
What the Symbols Mean
The parameters are presented in numerical order in the sections
that follow. Refer to Appendix C for a list of parameters cross-
referenced by parameter name.
Parameter Number: Unique number assigned to each
parameter.
Parameter Name: Unique name assigned to each
parameter.
Range: Predefined parameter limits or
selections. Note that a negative Hz
value indicates reverse rotation.
Default: Factory default setting.
See also: Associated parameters that may provide
additional or related information.
Symbol Meaning
Drive must be stopped before changing
parameter value.
32-bit parameter. Parameters marked
32-bit will have two parameter numbers
when using RS485 communications and
programming software.
32
- MD60 AC Drive 1
- User Manual 1
- Version 3.0 1
- CONTENTS 3
- Contents III 5
- IV MD60 AC Drive User Manual 6
- List of Figures 7
- VI MD60 AC Drive User Manual 8
- List of Tables 9
- MD60 AC Drive User Manual 10
- CHAPTER 1 11
- CHAPTER 2 13
- 2.3 Kits 15
- 2.4 Storage Guidelines 16
- CHAPTER 3 17
- 3.2 Mounting the Drive 20
- CHAPTER 4 21
- 4.1 RFI Filter Grounding 22
- CHAPTER 5 23
- V/T2T/L3S/L2R/L1 U/T1 W/T3 24
- • Install line reactor 26
- • Install isolation 26
- • Remove MOV jumper to 26
- ; 0 - 230 V, 3-Phase Output 29
- 200-600 Volt Installations 30
- 5.7 Reflected Wave Protection 31
- 5.8 Output Disconnect 32
- CHAPTER 6 33
- EN 60204-1:1992 34
- • Always use copper wire 34
- 6.4.1 I/O Wiring Examples 37
- Direction 39
- 6.6 Accel/Decel Selection 41
- CHAPTER 7 43
- Complete 44
- CHAPTER 8 45
- 8.1.1 Display Description 46
- • Parameter number 46
- • Parameter value 46
- • Fault code 46
- 8.1.2 LED Descriptions 46
- Table 8.2 – Key Descriptions 47
- 8.2 About Parameters 48
- Advanced (A) Parameters 49
- CHAPTER 9 51
- • Stop is removed and 53
- • Start is held active 53
- P037 Stop Mode 55
- P038 Speed Reference 56
- P039 Accel Time 1 57
- P040 Decel Time 1 57
- P041 Reset to Defaults 57
- 9.2 Advanced Group Parameters 58
- A055 Relay Output Select 59
- A056 Relay Output Level 61
- A067 Accel Time 2 61
- A068 Decel Time 2 62
- A069 Internal Frequency 62
- A080 DC Brake Time 64
- A081 DC Brake Level 64
- A082 DB Resistor Select 65
- A083 S Curve% 65
- A084 Start Boost 66
- A088 Maximum Voltage 67
- A089 Current Limit 67
- A090 Motor OL Select 67
- A091 PWM Frequency 68
- A092 Auto Restart Tries 68
- A093 Auto Restart Delay 69
- A094 Start At Power Up 69
- A095 Reverse Disable 69
- A096 Flying Start Enable 70
- A097 Compensation 70
- A098 SW Current Trip 71
- A100 Fault Clear 71
- A101 Program Lock 71
- A103 Comm Data Rate 72
- A104 Comm Node Address 72
- A105 Comm Loss Action 72
- A102 Testpoint Select 72
- A106 Comm Loss Time 73
- A107 Comm Format 73
- Range: 0.0 to 100.0% 74
- Default: 100.0% 74
- See also: A110, d020 74
- A114 Slip Compensation 75
- A115 Process Time Lo 76
- A116 Process Time Hi 76
- 9.3 Display Group Parameters 77
- Running Digit 0 78
- Forward Digit 1 78
- Accelerating Digit 2 78
- Decelerating Digit 3 78
- Parameter Descriptions 9-29 79
- Receiving Data Bit 0 81
- Transmitting Data Bit 1 81
- RS485 Option Connected Bit 2 81
- Fault Occurred Bit 3 81
- CHAPTER 10 83
- Feature) 84
- 10.2 Troubleshooting Tables 88
- APPENDIX A 93
- CSA 22.2 95
- APPENDIX B 97
- B.2 Advanced Parameter Group 98
- Record of User Settings B-3 99
- APPENDIX C 101
- APPENDIX D 105
- EN61000-3-2 107
- APPENDIX E 109
- Frame Model Number 110
- E.2 EMC Line Filters 111
- MD65 AC Drive User Manual 112
- Accessories E-5 113
- Description Model Number 114
- Accessories E-7 115
- Dimensions in mm and (in) 116
- APPENDIX F 117
- Parameter Configuration 118
- RS485 (MDI) Protocol F-3 119
- MD60 AC Drive User Manaul 120
- Table F.3 – Logic Commands 120
- Writing (06) Reference 121
- Reading (03) Feedback 122
- Codes) 123
- APPENDIX G 125
- Cable Accessories 126
- One Permanent Peripheral 127
- Connecting an RS485 Network 128
- Numerics 129
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation MD60 User Manual Version 3.0
Ekwipunek Rockwell-automation 284D On-Machine ArmorStart Accelerator Toolkit Instrukcja Użytkownika
(188 strony)
(188 strony)
Ekwipunek Rockwell-automation SB3000 Configuration and Programming Instrukcja Użytkownika
(122 strony)
(122 strony)
Ekwipunek Rockwell-automation 20D PowerFlex 700H/S Frame 13 Replacement Power St Instrukcja Użytkownika
(20 strony)
(20 strony)
(4 strony)
Ekwipunek Rockwell-automation T8834 Trusted 20 Channel Isolated AI/DI FTA Extern Instrukcja Użytkownika
(18 strony)
(18 strony)
Ekwipunek Rockwell-automation 440F 440F-C252D 22.5mm Control Unit Safedge Instrukcja Użytkownika
(2 strony)
(2 strony)
Ekwipunek Rockwell-automation T8831 Trusted 40 Channel Analogue FTA Non-incendiv Instrukcja Użytkownika
(14 strony)
(14 strony)
Ekwipunek Rockwell-automation Logix5000 Control Systems: Connect PanelView Plus Instrukcja Użytkownika
(56 strony)
(56 strony)
Ekwipunek Rockwell-automation 1440-SPD02-01RB XM-220 Dual Speed Module Instrukcja Użytkownika
(127 strony)
(127 strony)
Ekwipunek Rockwell-automation T8891 Trusted Speed Monitor OFTA (SOFTA) Instrukcja Użytkownika
(20 strony)
(20 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji