Rockwell Automation 1203-SSS Instrukcja Użytkownika Strona 64
- Strona / 112
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
B-4 Converter Parameters
PowerFlex 1203-USB Converter User Manual
Publication DRIVES-UM001D-EN-P
Parameters – SCANport
Drives (DriveExplorer or
DriveExecutive software
only)
No. Name and Description Details
01 [Adapter Port]
Displays the port on the host drive to which the
converter is connected.
Default: 0
Minimum: 0
Maximum: 7
Type: Read Only
02 [Reset Module]
No action if set to ‘0’ (Ready). Resets the converter if
set to ‘1’ (Reset Module). Restores the converter to its
factory default settings if set to ‘2’ (Set Defaults). This
parameter is a command. It will be reset to ‘0’ (Ready)
after the command has been performed.
Default: 0 = Ready
Values: 0 = Ready
1 = Reset Module
2 = Set Defaults
Type: Read/Write
Reset Required: No
03 [Clear DF1 Counts]
No action if set to ‘0’ (Ready). Resets the DF1
statistical Parameter 04 - [DF1 Packets Sent] and
Parameter 05 - [DF1 Packets Rcvd] to 0 (zero) if set
to ‘1’ (Clear Counts). This parameter is a command. It
will be reset to ‘0’ (Ready) after a ‘Clear Counts’
command has been performed.
Default: 0 = Ready
Values: 0 = Ready
1 = Clear Counts
Type: Read/Write
Reset Required: No
04 [DF1 Packets Sent]
Displays the number of DF1 packets sent by the
converter. The value of this parameter is normally
approximately equal to the value of Parameter 05 -
[DF1 Packets Rcvd].
Default: 0
Minimum: 0
Maximum: 65535
Type: Read Only
05 [DF1 Packets Rcvd]
Displays the number of DF1 packets received by the
converter. The value of this parameter is normally
approximately equal to the value of Parameter 04 - [DF1
Packets Sent].
Default: 0
Minimum: 0
Maximum: 65535
Type: Read Only
06 [Interface Mode]
Sets the interface operating mode.
Auto: The converter will automatically run DPI if
connected to a DPI drive, or SCANport if
connected to a SCANport drive.
SCANport: The converter will perform SCANport
services only.
Set this parameter to ‘0’ (Auto, the default) unless you
are using DriveTools32 software, version 2.xx, and you
are connected to a DPI drive. In this case, use the ‘1’
(SCANport) setting.
Default: 0 = Auto
Values: 0 = Auto
1 = SCANport
Type: Read/Write
Reset Required: Yes
!
ATTENTION: Risk of injury or equipment damage exists. If the converter is
transmitting I/O that controls the drive (indicated by a steady green diamond
status indicator), the drive may fault when you remove or reset the converter.
Determine how your drive will respond before removing or resetting a connected
converter.
- PowerFlex 1203-USB Converter 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- Chapter 4 Troubleshooting 6
- Appendix A Specifications 6
- Appendix F History of Changes 7
- About This Manual 9
- Additional Resources 10
- Getting Started 11
- Components 12
- Features 12
- Compatible Products 13
- Required Equipment 14
- User-Supplied Equipment 15
- Safety Precautions 16
- Quick Start 16
- Computer 17
- 1-8 Getting Started 18
- Installing the Converter 19
- Installing the USB Drivers 22
- Installing the Converter 2-5 23
- 2-6 Installing the Converter 24
- Installing the Converter 2-7 25
- 2-8 Installing the Converter 26
- Installing the Converter 2-9 27
- 2-10 Installing the Converter 28
- Installing the Converter 2-11 29
- Installing Connected 30
- Components Workbench 30
- Software 30
- Powering Up the Converter 30
- Removing the Converter 31
- 2-14 Installing the Converter 32
- Configuring the Converter 33
- Using Connected 34
- Configuring the Converter 3-3 35
- Configuring the Converter 3-5 37
- 3-6 Configuring the Converter 38
- to open the Linear List 38
- Resetting the Converter 39
- Updating the Firmware 40
- Using RTU Master Mode for 40
- Configuring the Converter 3-9 41
- Establishing Communication 42
- to open the RSWho window 45
- Troubleshooting 49
- Diamond Status Indicator 50
- RX Status Indicator 50
- TX Status Indicator 50
- Converter Diagnostic Items 51
- Viewing Diagnostic Data 52
- Troubleshooting 4-5 53
- Converter Events 54
- Event Codes for DSI Drives 55
- Viewing and Clearing 56
- Viewing and Clearing DF1 57
- Communication Statistics 57
- Troubleshooting Potential 58
- Problems 58
- Specifications 59
- Environmental 60
- Agency Certification 60
- Converter Parameters 61
- Parameters – DSI Drives 62
- Parameters – SCANport 64
- Drives (DriveExplorer or 64
- DriveExecutive software 64
- Appendix C 65
- Preparing for a Firmware 68
- Viewing and Clearing Events 70
- Appendix D 75
- Appendix E 91
- Updating Firmware 95
- History of Changes 99
- F-2 History of Changes 100
- Glossary 101
- D DF1 Protocol 102
- N NVS (Non-Volatile Storage) 103
- S SCANport 104
- U Update 104
- X Xmodem 104
- Z Zero Data 105
- G-6 Glossary 106
- Rockwell Automation Support 112
- Documentation Feedback 112
Powiązane produkty i podręczniki dla Networking Rockwell Automation 1203-SSS
(20 strony)ENERGY SISTEM Energy Tablet 7 Neo 2 manuales
Manuales del propietario y guías del usuario para Tabletas ENERGY SISTEM Energy Tablet 7 Neo 2.
Ofrecemos 1 manuales en pdf ENERGY SISTEM Energy Tablet 7 Neo 2 para descargar gratis por tipos de documentos: Manual de usuario
Komentarze do niniejszej Instrukcji