Rockwell-automation 1746-NR4 SLC RTD/Resistance Input Module User Manu Instrukcja Użytkownika Strona 125
- Strona / 148
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
125 Publication 1746-UM008B-EN-P - December 2006
Appendix
C
Configuration Worksheet
for RTD/Resistance Module
The following configuration procedure and worksheet are provided to
help you configure each of the channels on your RTD module. The
channel configuration word consists of bit fields, the settings of which
determine how the channel will operate. This procedure looks at each
bit field separately and helps you configure a channel for operation.
Refer to the Channel Configuration Word (O:e.0 through O:e.3) - Bit
Definitions table and the detailed configuration information in
Chapter 5 as needed to complete the procedures in this appendix. Or
you may prefer to use the summary worksheet on page 128.
Channel Configuration
Procedure
Proceed as follows.
1. Determine the input device type (RTD type or resistance input)
for a channel and enter its respective 4-digit binary code in bit
field 0…3 of the channel configuration word.
Bits 0-3
RTD Sensors/Setting
Resistance
Input/Setting
Platinum
(∝ = 0.00385)
Platinum
(∝ = 0.003916)
Copper
(∝ = 0.00426)
Nickel
(∝ = 0.00618)
(∝ = 0.00672)
Nickel Iron
(∝ = 0.00518)
Select
Input Type
100 Ω 0000 100 Ω 0100
10 Ω
(1)
1000 120 Ω 1001 604 Ω 1011 150 Ω 1100
200 Ω 0001 200 Ω 0101 - - 120
Ω
(2)
1010 - - 500 Ω 1101
500 Ω 0010 500 Ω 0110 - - - - - - 1000 Ω 1110
1000 Ω 0011 1000 Ω 0111 - - - - - - 3000 Ω 1111
(1)
Actual value at 0 °C (32 °F) is 9.042 Ω per SAMA standard RC21-4-1966.
(2)
Actual value at 0 °C (32 °F) is 100 Ω per DIN standard.
- SLC 500 1
- RTD/Resistance 1
- Input Module 1
- Important User Information 2
- Summary of Changes 3
- New Information 3
- 4 Summary of Changes 4
- Table of Contents 5
- 6 Table of Contents 6
- Use This Manual 7
- Who Should Use This 7
- Purpose of This Manual 7
- Contents of this Manual 8
- Common Techniques Used 9
- 10 Preface 10
- Overview 11
- 12 Overview 12
- RTD Compatibility 13
- 14 Overview 14
- Overview 15 15
- Hardware Overview 16
- System Overview 18
- System Operation 19
- LED Indicator Status 20
- 22 Overview 22
- Quick Start Guide 23
- Procedures 24
- Insert the Module 25
- Wire the Module 25
- Configure Your I/O 28
- Output Image Detail 29
- 30 Quick Start Guide 30
- Input Image Detail 31
- Monitoring Status 32
- Install and Wire the Module 33
- NR4 Power Requirements 34
- Module Location in Chassis 35
- General Considerations 37
- Module Installation and 38
- Install the Module 39
- Remove the Module 39
- Terminal Wiring 40
- IMPORTANT 41
- Cable Examples 46
- Calibration 47
- Single-point Calibration 48
- Module ID Code 51
- Module Addressing 52
- O : 4 . 2 53
- I : 3 . 6 53
- Channel Filter Frequency 54
- Selection 54
- Effective Resolution 55
- 10 Hz Filter Notch Frequency 56
- 50 Hz Filter Notch Frequency 57
- 60 Hz Filter Notch Frequency 57
- 250 Hz Filter Notch Frequency 57
- Scanning Process and 58
- Channel Timing 58
- Scanning Cycle 60
- Channel Turn-on, Turn-off 61
- Response to Slot Disabling 61
- Input Response 62
- Output Response 62
- Procedure 64
- Enter the Configuration Data 65
- Scaled–for–PID 68
- Temperature Counts 69
- -200 °C (-328 °F) -32,768 69
- +630 °C (1166 °F) +32,767 69
- Scaling Examples 71
- 1746-NR4 73
- Scaling Select (Bits 13-14) 78
- User-set Scaling 79
- Limit Scale Words 80
- Channel Data Word 81
- Channel Status Checking 82
- Bits Define 83
- These bit settings 83
- Indicate this 83
- 1514131211109876543210 83
- Input Type Status (Bits 0…3) 84
- Excitation Current (Bit 12) 85
- Broken Input Error (Bit 13) 85
- Out-of-range Error (Bit 14) 86
- Configuration Error (Bit 15) 86
- Ladder Programming Examples 87
- Initial Programming 88
- Configuration Word Setup 89
- Copy File Data Flow 89
- Programming Procedure 90
- Dynamic Programming 91
- Verify Channel 92
- Configuration Changes 92
- Interface to the PID 93
- Instruction 93
- Use the Proportional 95
- Counts Data Format with 95
- Monitor Channel Status 96
- Invoke Autocalibration 97
- Introduction 99
- Module Operation vs 99
- Channel Operation 99
- Power Turn-on Diagnostics 100
- Channel Diagnostics 100
- LED Indicators 100
- Error Codes 102
- Out-of-range Detection 103
- Troubleshooting Flowchart 105
- Replacement Parts 106
- Contact Rockwell 106
- Automation 106
- Application Examples 107
- Channel Configuration 108
- Program Listing 109
- Program to Convert °F to BCD 110
- Supplementary Example 111
- Degrees Selector Switch 114
- Specifications 117
- 118 Specifications 118
- Module Accuracy 119
- 120 Specifications 120
- Specifications 121 121
- 122 Specifications 122
- RTD Standards 123
- 124 RTD Standards 124
- Configuration Worksheet 125
- I/O Configuration 131
- 132 I/O Configuration 132
- I/O Configuration 133 133
- 6. Click OK 134
- Glossary 135
- 136 Glossary 136
- Glossary 137 137
- 138 Glossary 138
- 140 Index 140
- Index 141 141
- 142 Index 142
- How Are We Doing? 143
- BUSINESS REPLY MAIL 144
- Rockwell Automation 148
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 1746-NR4 SLC RTD/Resistance Input Module User Manu
Ekwipunek Rockwell-automation 1757-FIMRTP ProcessLogix Remote Termination Panel Instrukcja Użytkownika
(12 strony)
(12 strony)
Ekwipunek Rockwell-automation 1734-IK/C POINT I/O 5V and 24V Encoder/Counter Mod Instrukcja Użytkownika
(24 strony)
(24 strony)
Ekwipunek Rockwell-automation 1756-OF8I ControlLogix Eight-channel Isolated Anal Instrukcja Użytkownika
(208 strony)
(208 strony)
Ekwipunek Rockwell-automation 1734-IE8C Installation Instructions Instrukcja Użytkownika
(24 strony)
(24 strony)
Ekwipunek Rockwell-automation 1747-L40 SLC 500 Fixed Hardware Style Instrukcja Użytkownika
(223 strony)
(223 strony)
Ekwipunek Rockwell-automation 1762-OV32T MicroLogix Solid State 24V DC Sink Outp Instrukcja Użytkownika
(20 strony)
(20 strony)
Ekwipunek Rockwell-automation 1766-Lxxxx MicroLogix 1400 Programmable Controller Instrukcja Użytkownika
(406 strony)
(406 strony)
Ekwipunek Rockwell-automation 1769-IT6 Compact I/O 1769-IT6 Thermocouple/mV Inpu Instrukcja Użytkownika
(168 strony)
(168 strony)
Ekwipunek Rockwell-automation 1792-IB8XOB8PLP INSTL INSTR ARMORBLOCK LP 8/8 Instrukcja Użytkownika
(12 strony)
(12 strony)
Ekwipunek Rockwell-automation 1792-IB4/B INSTL.INST ARMORBLOCK 4 INPUT Instrukcja Użytkownika
(36 strony)
(36 strony)
Ekwipunek Rockwell-automation 1747-PBASE BASIC Development Software Programming Instrukcja Użytkownika
(144 strony)
(144 strony)
(1 strony)
Ekwipunek Rockwell-automation 1746-NT4 SLC 500 Thermocouple/mV Input Module Inst Instrukcja Użytkownika
(24 strony)
(24 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji