Rockwell-automation 1790D-XXXX DeviceNet Analog Base Terminal Block Co Instrukcja Użytkownika

1 Publication 1790-IN002B-EN-P -April 2003Installation InstructionsDeviceNet Analog Base Termina

10 Publication 1790-IN002B-EN-P - April 2003Connect the DeviceNet CableFollow these procedures when connecting the DeviceNet cable to the bas

11Publication 1790-IN002B-EN-P - April 2003Once you have properly wired the drop line to the connector, attach the connector to the block. If

12 Publication 1790-IN002B-EN-P - April 20031790D-TN0C2, -TN0V2 Output Data FileWord/Bit Descriptions for 1790D-TN0C2, -TN0V2 Analog Output M

13Publication 1790-IN002B-EN-P - April 2003I/O Channel LED Status Indicator1790D-TN4V0 1790D-TN4C0Status: Description: Status: Description:Fl

14 Publication 1790-IN002B-EN-P - April 2003DeviceNet Analog Base Terminal Block SpecificationsThe following table contains specifications th

15Publication 1790-IN002B-EN-P - April 2003Vibration 2g @ 10-500HzIEC60068-2-6 (Test Fc, Operating)Shock Operating Non-oper

16 Publication 1790-IN002B-EN-P - April 20031 Refer to publication 1770-4.1, Programmable Controller Wiring and Grounding Guidelines.2 See th

17Publication 1790-IN002B-EN-P - April 20034-Channel Analog Current Input Module Specifications1790D-TN4C0Inputs per module 4 channel single-

18 Publication 1790-IN002B-EN-P - April 20032 Channel Analog Current Output Module Specifications1790D-TN0C2Outputs per module 2 channel sing

19Publication 1790-IN002B-EN-P - April 20034 Channel Analog Voltage Input Module Specifications1790D-TN4V0Inputs per module 4 channel single-

2 Publication 1790-IN002B-EN-P - April 2003Important User InformationBecause of the variety of uses for the products described in this public

20 Publication 1790-IN002B-EN-P - April 20032 Channel Analog Voltage Output Module Specifications1790D-TN0V2Outputs per module 2 channel sing

21Publication 1790-IN002B-EN-P - April 2003IMPORTANTInput and output wiring must be in accordance with Class 1, Division 2 wiring methods and

22 Publication 1790-IN002B-EN-P - April 2003The following information applies when operating this equipment in hazardous locations:Informatio

23Publication 1790-IN002B-EN-P - April 2003

Publication 1790-IN002B-EN-P - April 2003 PN 957782-24Supersedes Publication 1790-IN002A-EN-P - December 2001 © 2003 Rockwell A

3Publication 1790-IN002B-EN-P - April 2003ATTENTION!Identifies information about practices or circumstances that can lead to personal injury

4 Publication 1790-IN002B-EN-P - April 2003ATTENTION!Environment and EnclosureThis equipment is intended for use in a Pollution Degree 2 indu

5Publication 1790-IN002B-EN-P - April 2003Installing CompactBlock LDX I/OFollow these steps to install the block:1. Set the node address on t

6 Publication 1790-IN002B-EN-P - April 2003Mount the Base BlockYou can mount the base block to a panel or DIN rail. We recommend that you gro

7Publication 1790-IN002B-EN-P - April 20035. Replace the block on the panel and place a screw through each of the two mounting holes. Tighten

8 Publication 1790-IN002B-EN-P - April 2003Mount the Optional Expansion BlocksMount the expansion block by connecting it to a previously-inst

9Publication 1790-IN002B-EN-P - April 20031790D-TN4CO Current Analog Input Module Terminal Block Wiring• Wire pin 1 to Field Power (+) 24VdcW