Rockwell-automation 1794-OB16D FLEX I/O Diagnostic Modules User Manual Instrukcja Użytkownika Strona 21
- Strona / 132
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
19 Publication 1794-UM061A-EN-P - July 2006
2
About the FLEX I/O Diagnostic Input Module
Introduction
In this chapter, you will learn about the diagnostic input module, cat. no.
1794-IB16D.
About the 1794-IB16D
Diagnostic Input Module
The 1794-IB16D diagnostic input module provides 16 points of 24V dc
sinking inputs with open-wire, short-circuit, and user supply reverse polarity
diagnostic features. Each input signal has an associated sensor power
connection. The module monitors current and voltage at each input channel
sensor power terminal.
The module detects:
• an open fault if the sensor-power current drops.
• a short fault if the sensor-power voltage goes low.
• a reverse-polarity fault if reverse voltage is applied to the user terminals.
For Information About See Page
About the 1794-IB16D Diagnostic Input Module 19
Diagnostic Fault Detection 21
Indicator Status Information 2
Module Limitations 24
Configure Your Diagnostic Input Module 26
- FLEX I/O Diagnostic Modules 1
- Important User Information 2
- Table of Contents 3
- Table of Contents iv 4
- Appendix A 5
- Appendix B 5
- Digital Modules 5
- Table of Contents vi 6
- Purpose of This Manual 7
- Important Warnings and 7
- Cautions 7
- Hazardous Location approved 9
- Related Products and 10
- Documentation 10
- Preface 9 11
- 10 Preface 12
- Preface 11 13
- 12 Preface 14
- Overview 15
- Network Compatibility 16
- Output Module 18
- Base Units) 20
- Introduction 21
- About the 1794-IB16D 21
- Diagnostic Input Module 21
- Input Channels 0-15 22
- Diagnostic Fault Detection 23
- Indicator Status 25
- Information 25
- Module Limitations 26
- Unused Sensor Power Ports 27
- Configure Your Diagnostic 28
- Input Module 28
- About the 1794-OB16D 29
- Diagnostic Output Module 29
- (1794-TB3 shown) 30
- Module Protection 32
- Functions 32
- Indicator Status Information 33
- Configure Your Output 34
- Diagnostic Module 34
- Remote I/O Network 35
- Add a 1756-DHRIO Module 36
- ATTENTION 38
- Add a 1794 Remote Adapter 39
- Configure Digital Modules 42
- Create a Block Transfer 44
- (Read or Write) Message 44
- Instruction 44
- Ladder Logic Examples 48
- DeviceNet Network 49
- Bandwidth 50
- Determine the Address of 54
- DeviceNet Data 54
- Tally Memory 56
- Requirements 56
- Configuration 57
- Offline 57
- Set the Address of the 58
- Select a 61
- Communication Format 61
- Ownership 66
- Add Local and Remote 67
- ControlNet Modules 67
- Add Distributed I/O 68
- Download the Program to 70
- Configure the 1794-ACN15 71
- Schedule I/O Module 72
- Connections 72
- 6. Click OK 73
- File and Save 73
- Access Module Data via 77
- Change Configuration Data 79
- EtherNet/IP Network 83
- Set Up the Hardware 84
- Select a Requested Packet 84
- Interval (RPI) 84
- Select a Communication 85
- Select a Remote Adapter 89
- Access Distributed I/O 93
- General Information About 95
- IP Addresses 95
- Assigning Network 96
- Parameters via the 96
- BOOTP/DHCP Utility 96
- Using Other Methods to 99
- Assign Network 99
- Parameters 99
- Duplicate IP Address 102
- Detection 102
- Duplicate detection scenarios 103
- IP Address Swapping 104
- Interpret the Indicators 105
- Functional Details 106
- 1794-IB16D Diagnostic 106
- For 3-wire sensors: 107
- 1794-OB16D Diagnostic 109
- (20 KΩ + 110
- Appendix 111
- Find Your Module 111
- *Fuse on 1794-TBNF only 113
- * Fuse on 1794-TBNF only 114
- Flexbus Interface 117
- 1794-OW8 Relay Output Module 126
- 126 Index 128
- How Are We Doing? 129
- BUSINESS REPLY MAIL 130
- Rockwell Automation 132
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 1794-OB16D FLEX I/O Diagnostic Modules User Manual
Ekwipunek Rockwell-automation 9303 DriveTools Software Reference Card Instrukcja Użytkownika
(3 strony)
(3 strony)
Ekwipunek Rockwell-automation 45C67 Dual Output Module/AutoMate/AutoMax/DCS Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Rockwell-automation 2711-NP2 Mounting Clips for PanelView 600, 900, 10 Instrukcja Użytkownika
(12 strony)
(12 strony)
Ekwipunek Rockwell-automation 2706-LV2S_LV4S DL40 PLUS SLAVE USER MANUAL Instrukcja Użytkownika
(60 strony)
(60 strony)
Ekwipunek Rockwell-automation 61C516 AutoMax/AutoMate 24VAC/DC Input Module Instrukcja Użytkownika
(38 strony)
(38 strony)
Ekwipunek Rockwell-automation 2706-F11J_F11JC_F21J_F21JC DL50 INSTALLATION MANUA Instrukcja Użytkownika
(135 strony)
(135 strony)
Ekwipunek Rockwell-automation 2711P-RTFC Mounting Levers for PanelView Plus 400 Instrukcja Użytkownika
(16 strony)
(16 strony)
Ekwipunek Rockwell-automation 1798-OE2 FlexArmor Analog Output Module Instrukcja Użytkownika
(8 strony)
(8 strony)
Ekwipunek Rockwell-automation 9323-PA2E APS SLC 500 Import/Export Utility User M Instrukcja Użytkownika
(110 strony)
(110 strony)
Ekwipunek Rockwell-automation 61C350 2-In/2-Out 0-10 Volt Analog Rail Module Instrukcja Użytkownika
(48 strony)
(48 strony)
Ekwipunek Rockwell-automation 7477-IC2VC PlantPAx Server and Workstation Bundles Instrukcja Użytkownika
(35 strony)
(35 strony)
Ekwipunek Rockwell-automation 6181 Industrial Computer CPU Upgrade Instrukcja Użytkownika
(4 strony)
(4 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji