Rockwell-automation 22-COMM-C ControlNet Adapter Instrukcja Użytkownika Strona 116
- Strona / 164
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
B-2 Adapter Parameters
04 [CN Rate Cfg]
Sets the ControlNet data rate (megabits per
second) at which the adapter communicates.
(Updates Parameter 05 - [CN Rate Act] after a
reset.)
Default: 0 = 5 Mbps
Values: 0 = 5 Mbps
Type: Read/Write
Reset Required: Yes
05 [CN Rate Act]
Displays the ControlNet data rate (megabits per
second) actually used by the adapter.
Default: 0 = 5 Mbps
Values: 0 = 5 Mbps
Type: Read Only
06 [CN Active Cfg]
Displays the source from which the adapter node
address is taken. This will either be switches or
Parameter 02 - [CN Addr Cfg] in EEPROM. It is
determined by the settings of the Node Address
Switches on the adapter. If the Node Address
Switches = “00” on power up, then Parameter 02 -
[CN Addr Cfg] is used to configure the adapter’s
ControlNet address.
Default: 0 = Switches
Values: 0 = Switches
1 = EEPROM
Type: Read Only
07 [Reset Module]
No action if set to “Ready.” Resets the adapter if
set to “Reset Module.” Restores the adapter to its
factory default settings if set to “Set Defaults.” This
parameter is a command. It will be reset to “0 =
Ready” after the command has been performed.
Default: 0 = Ready
Values 0 = Ready
1 = Reset Module
2 = Set Defaults
Type: Read/Write
Reset Required: No
08 [Comm Flt Action]
Sets the action that the adapter and drive will take
if the adapter detects that network
communications have been disrupted. This setting
is effective only if I/O that controls the drive is
transmitted through the adapter.
Default: 0 = Fault
Values: 0 = Fault
1 = Stop
2 = Zero Data
3 = Hold Last
4 = Send Flt Cfg
Type: Read/Write
Reset Required: No
Parameter
No. Name and Description Details
!
ATTENTION: Risk of injury or equipment damage exists. If the adapter is
transmitting I/O that controls the drive, the drive may fault when you reset the
adapter. Determine how your drive will respond before resetting a connected
adapter.
!
ATTENTION: Risk of injury or equipment damage exists. Parameter 08 - [Comm
Flt Action] lets you determine the action of the adapter and connected drive if
communications are disrupted. By default, this parameter faults the drive. You
can set this parameter so that the drive continues to run. Precautions should be
taken to ensure that the setting of this parameter does not create a risk of injury
or equipment damage. When commissioning the drive, verify that your system
responds correctly to various situations (for example, a disconnected drive).
- ControlNet 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- Chapter 8 Troubleshooting 6
- Appendix A Specifications 6
- Appendix B Adapter Parameters 6
- About This Manual 9
- Rockwell Automation Support 11
- P-4 About This Manual 12
- Getting Started 13
- Features 14
- Compatible Products 15
- Required Equipment 15
- Safety Precautions 16
- Quick Start 17
- Modes of Operation 18
- Installing the Adapter 19
- Node Address 20
- Switches 20
- Operating 20
- Mode Jumper 20
- Item Description 22
- DSI connector 22
- ControlNet cable 22
- Installing the Adapter 2-5 23
- Applying Power 25
- 2-8 Installing the Adapter 26
- Configuring the Adapter 27
- Using the HIM 28
- Setting the Node Address 29
- Setting the I/O Configuration 29
- Setting a Fault Action 30
- To change the fault action 31
- Resetting the Adapter 32
- Configuring the Adapter 3-7 33
- 3-8 Configuring the Adapter 34
- Configuring the I/O 35
- Configuring the I/O 4-7 41
- 4-10 Configuring the I/O 44
- PLC-5 Example 46
- Using the I/O 51
- Understanding the I/O Image 52
- Using Logic Command/Status 53
- Using Reference/Feedback 53
- ControlLogix Example 55
- 5-6 Using the I/O 56
- Using the I/O 5-7 57
- Using the I/O 5-9 59
- Figure 6.5 59
- 5-10 Using the I/O 60
- Using Explicit Messaging 61
- Ladder Logic Program 65
- Using Multi-Drive Mode 69
- 1 drive per node 70
- System Wiring 72
- 7-6 Using Multi-Drive Mode 74
- Adapter Settings 76
- Drive Settings 76
- ControlLogix I/O Example 77
- 7-10 Using Multi-Drive Mode 78
- 7-12 Using Multi-Drive Mode 80
- Using Multi-Drive Mode 7-13 81
- 7-14 Using Multi-Drive Mode 82
- Using Multi-Drive Mode 7-15 83
- 7-16 Using Multi-Drive Mode 84
- Using Multi-Drive Mode 7-17 85
- 7-18 Using Multi-Drive Mode 86
- Using Multi-Drive Mode 7-19 87
- 7-20 Using Multi-Drive Mode 88
- Using Multi-Drive Mode 7-21 89
- PLC-5 I/O Example 92
- Using Multi-Drive Mode 7-25 93
- 7-26 Using Multi-Drive Mode 94
- Using Multi-Drive Mode 7-27 95
- 7-28 Using Multi-Drive Mode 96
- Using Multi-Drive Mode 7-29 97
- 7-30 Using Multi-Drive Mode 98
- Using Multi-Drive Mode 7-31 99
- 7-32 Using Multi-Drive Mode 100
- Using Multi-Drive Mode 7-33 101
- 7-34 Using Multi-Drive Mode 102
- Using Multi-Drive Mode 7-35 103
- Additional Information 104
- Troubleshooting 105
- PORT Status Indicator 106
- MOD Status Indicator 107
- 8-4 Troubleshooting 108
- Troubleshooting 8-5 109
- (version 3.01 or higher) 109
- 8-6 Troubleshooting 110
- Viewing and Clearing Events 111
- 8-8 Troubleshooting 112
- Specifications 113
- Environmental 114
- Regulatory Compliance 114
- Adapter Parameters 115
- B-2 Adapter Parameters 116
- Adapter Parameters B-3 117
- B-4 Adapter Parameters 118
- ControlNet Objects 119
- Identity Object 120
- Identity Object (Continued) 121
- Assembly Object 122
- Assembly Object (Continued) 123
- Register Object 124
- Register Object (Continued) 125
- Parameter Object 127
- Parameter Object (Continued) 128
- Class Code 130
- Services 130
- Instances 130
- Class Attributes 130
- Instance Attributes 131
- (Continued) 131
- PCCC Object 132
- PCCC Object (Continued) 133
- DSI Device Object 138
- DSI Device Object (Continued) 139
- DSI Parameter Object 141
- Descriptor Attributes 143
- Formulas for Converting 144
- Common Services 144
- Object Specific Services 144
- DSI Fault Object 145
- DSI Fault Object (Continued) 146
- DSI Diagnostic Object 147
- Logic Command/Status Words 149
- Logic Status Word 150
- Glossary 151
- D Data Rate 152
- F Fault Action 153
- I I/O Data 153
- L Logic Command/Logic Status 154
- N Node Address 154
- R Reference/Feedback 154
- S Scanner 155
- Z Zero Data 155
- G-6 Glossary 156
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 22-COMM-C ControlNet Adapter
Ekwipunek Rockwell-automation 20P PowerFlex DC Drive - Frame C AC Line Snubber B Instrukcja Użytkownika
(16 strony)
(16 strony)
Ekwipunek Rockwell-automation 20P PowerFlex DC Drive - Frame C Bimetal Thermosta Instrukcja Użytkownika
(16 strony)
(16 strony)
(4 strony)
Ekwipunek Rockwell-automation 22B PowerFlex 40 Quick Start FRN 5.xx - 6.xx Instrukcja Użytkownika
(22 strony)
(22 strony)
Ekwipunek Rockwell-automation 20P PowerFlex DC Drive - Frame D Snubber Resistors Instrukcja Użytkownika
(10 strony)
(10 strony)
Ekwipunek Rockwell-automation 20P PowerFlex DC Drive - Frame A Field SCR/Dual Di Instrukcja Użytkownika
(14 strony)
(14 strony)
Ekwipunek Rockwell-automation 20A PowerFlex 70 Adjustable Frequency AC Drive Instrukcja Użytkownika
(56 strony)
(56 strony)
Ekwipunek Rockwell-automation 1336S_F_T_E_R C-Frame Front End Conversion Kit Instrukcja Użytkownika
(8 strony)
(8 strony)
Sony PCG-808 manuales
Manuales del propietario y guías del usuario para Cuadernos Sony PCG-808.
Ofrecemos 1 manuales en pdf Sony PCG-808 para descargar gratis por tipos de documentos: Manual de usuario
Komentarze do niniejszej Instrukcji