Rockwell-automation 284G ArmorStart - Getting Started Instrukcja Użytkownika Strona 1

QUICK STARTARMORSTART® DISTRIBUTED MOTOR CONTROLLERGetting StartedBULLETIN 284G Introduction This guide provides the basic information required to sta

10 Publication 284G-QS001A-EN-P - December 2008• Using an EMI filter with any drive rating, may result in relatively high ground leakage curren

Publication 284G-QS001A-EN-P - December 2008 11DeviceNet Node CommissioningEstablishing a DeviceNet Node AddressThe ArmorStart is shipped with

12 Publication 284G-QS001A-EN-P - December 2008Node Commissioning using HardwareThe ArmorStart is shipped with the hardware rotary switches set

Publication 284G-QS001A-EN-P - December 2008 13Using Automap Feature with Default Input and Output (I/O) AssembliesThe Automap feature availabl

14 Publication 284G-QS001A-EN-P - December 2008Setting the Motor OL CurrentThe product should now be configured and communicating on the networ

Publication 284G-QS001A-EN-P - December 2008 15Table 6 Basic Program Group for Sensorless Vector Control➊ Stop drive before changing this param

16 Publication 284G-QS001A-EN-P - December 2008Quick Reference TroubleshootingThere are four LEDs on the front of the ArmorStart that can provi

Publication 284G-QS001A-EN-P - December 2008 17Fault LED Indications for Bulletin 284G ArmorStart Distributed Motor ControllersTable 9 Controll

18 Publication 284G-QS001A-EN-P - December 2008Internal Drive FaultsA fault is a condition that stops the drive. There are two fault types.Tabl

Publication 284G-QS001A-EN-P - December 2008 19Table 11 Fault Types, Descriptions, and Actions➊ See Table 10 for internal drive fault types.No.

2 Publication 284G-QS001A-EN-P - December 2008Installation The ArmorStart Distributed Motor Controller is convection cooled. Operating temperat

20 Publication 284G-QS001A-EN-P - December 2008Table 12 Fault Types, Descriptions, and Actions (Continued)➊ See Table 10 for internal drive fa

Publication 284G-QS001A-EN-P - December 2008 21Figure 9 Bulletin 284G ArmorStartLED StatusIndicationMotorConnectorDeviceNetConnection(Mini/M18)

22 Publication 284G-QS001A-EN-P - December 2008Accessories Table 12 DeviceNet Media ➊0➊See Publication M116-CA001A-EN-P for complete cable sele

Publication 284G-QS001A-EN-P - December 2008 23Table 13 Sensor Media ➊0➊See Publication M116-CA001A-EN-P for complete cable selection informati

Publication 284G-QS001A-EN-P — December 2008 PN-29250Copyright ©2008 Rockwell Automation, Inc. All Rights Reserved. Printed in USA.Registered Trademar

Publication 284G-QS001A-EN-P - December 2008 3Dimensions are shown in millimeters (inches). Dimensions are not intended to be used for manufact

4 Publication 284G-QS001A-EN-P - December 2008Wiring Power, Control, and Ground Wiring Table 1 provides the power, control, and ground wire cap

Publication 284G-QS001A-EN-P - December 2008 5ArmorConnect Power Media DescriptionThe ArmorStart Power Media offers both three-phase and contro

6 Publication 284G-QS001A-EN-P - December 2008Figure 5 Control Power Media System Overview➏ Control Power Media Patchcords - PatchCord cable w

Publication 284G-QS001A-EN-P - December 2008 7ArmorStart with ArmorConnect Connectivity Terminal DesignationsTerminal Designations Descriptio

8 Publication 284G-QS001A-EN-P - December 2008ArmorConnect Cable RatingsThe ArmorConnect Power Media cables are rated per UL Type TC 600V 90 °C

Publication 284G-QS001A-EN-P - December 2008 9*Historically cable meeting these crush and impact requirements were designated and marked “Open