Rockwell-automation 6000 PowerFlex Medium Voltage Variable Frequency D Instrukcja Użytkownika Strona 20
- Strona / 98
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
20 Rockwell Automation Publication 6000-IN006A-EN-P - April 2014
Chapter 1 Shipping and Handling Procedures
3. Align and secure the lifting angles in six places as shown in Figure 7 using
the hardware removed in step 2.
Figure 7 - Install Fasteners from the Lifting Angles to the Drive in six places
4. Install the supplied hardware (M12 bolt and nut, two flat washers) to join
the lifting angles together in three places (Figure 8
).
Figure 8 - Bolt vertical slots on the Lifting Angles in three places
Attach the Overhead Lifting Cables
1. Attach rigging assembly firmly to the lifting angles on the top of the Power
Module/LV Control Cabinet (Figure 9
).
Lifting Angle Pair
M20 x 60
Lockwasher
Washer
M12 Nut
M12 Bolt
Washer
ATTENTION: The load carrying capacity of the lifting device and rigging must
be sufficient to safely raise the cabinet. Check the shipping weights by referring
to the container’s commercial invoice.
- Installation Instructions 1
- Important User Information 2
- Table of Contents 3
- Chapter 3 4
- Drive Electrical Installation 4
- Chapter 4 4
- General Precautions 8
- Commissioning Support 8
- Additional Resources 8
- Contractor Scope of Work 9
- Chapter 1 11
- Overview 11
- General Handling 12
- Information 12
- Offloading and Moving 12
- Unpack and Inspect the Drive 13
- Drive Configurations 14
- Installation Site 15
- Requirements 15
- Initial Inspection Checklist 15
- Mounting Clearance Distance 16
- Mounting Requirements 16
- Channel Steel Base 17
- Remove the Wooden Skids 18
- Overhead Lifting 19
- Lift the Power Module/LV 19
- Control Cabinet 19
- Figure 10 - Insert bolts 22
- Lift the Isolation 23
- Transformer Cabinet 23
- Lift the Bypass Cabinet 26
- Drive Mechanical Installation 27
- (see step 3 28
- Table 6 - Sidesheet Openings 29
- Affix Cabinets to Floor 31
- Figure 21 - Welding locations 32
- Install Main Cooling Fans 33
- Install Drawout Power 34
- Modules (if applicable) 34
- Install Power Modules 36
- External Ducting 38
- Air Conditioning Sizing 39
- Electrical Drawings 42
- Grounding System 42
- Power Cable Insulation 43
- Power Cable Design 44
- Considerations 44
- Motor Cable Sizing 44
- Control Signal Wiring Design 45
- Table 10 - Power Terminals 48
- Bypass Cabinet) 49
- Cabinet) 49
- Connect Control Power 50
- Connect External Control 52
- Signal Wiring 52
- Connect Electrical Safety 53
- Interlock Circuit to Input 53
- Circuit Breaker 53
- Introduction 53
- Wire Routing and Connection 54
- Electrical Interconnection 55
- Power Cable Interconnection 56
- Connect Isolation 57
- Transformer Secondary 57
- Power Cables 57
- Cable Routing and Connection 59
- Connect Motor and Voltage 60
- Sensing Board Cables 60
- Connect LV Control and 62
- Fan Wiring Bundles 62
- Connect Ground Bus 65
- Complete the Installation 65
- Pre-Commissioning 67
- Pre-Commissioning Checklist 68
- Table 14 - Control Wiring: 69
- Table 15 - Power Wiring: 69
- Torque Requirements 71
- General Wire Categories 73
- Appendix D 75
- Appendix E 83
- Appendix F 85
- Schematic Diagrams 85
- Standard Input/Output 89
- Connection Points 89
- Line and Load Cable Sizes 91
- Rockwell Automation Support 98
- Documentation Feedback 98
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 6000 PowerFlex Medium Voltage Variable Frequency D
Ekwipunek Rockwell-automation 2098-UWCPRG Ultraware Software User Manual Instrukcja Użytkownika
(354 strony)
(354 strony)
Ekwipunek Rockwell-automation 2364F RGU Isolation Board Replacement Instrukcja Użytkownika
(6 strony)
(6 strony)
Ekwipunek Rockwell-automation 1797-RPFM ControlNet Ex Modular Repeater Adapter F Instrukcja Użytkownika
(32 strony)
(32 strony)
Ekwipunek Rockwell-automation 2705-ND1 Keypad Development Software Instrukcja Użytkownika
(123 strony)
(123 strony)
Ekwipunek Rockwell-automation 2100 Redesign Unit Bus Stab Moldings Instrukcja Użytkownika
(2 strony)
(2 strony)
Ekwipunek Rockwell-automation 2097-Vxxx Kinetix 350 Single-axis EtherNet/IP Serv Instrukcja Użytkownika
(156 strony)
(156 strony)
Ekwipunek Rockwell-automation 8510 AC Spindle Drive Reference Card Instrukcja Użytkownika
(1 strony)
(1 strony)
Ekwipunek Rockwell-automation 2706-NP3 DL20 OFFLINE PROGRAMMING MANUAL Instrukcja Użytkownika
(67 strony)
(67 strony)
Ekwipunek Rockwell-automation 2098-IPD-xxx Ultra5000 Intelligent Positioning Dri Instrukcja Użytkownika
(160 strony)
(160 strony)
Ekwipunek Rockwell-automation 7000 PowerFlex Medium Voltage Air-Cooled (B Frame) Instrukcja Użytkownika
(28 strony)
(28 strony)
Ekwipunek Rockwell-automation 2711-ND3 PanelBuilder v2.60 Software User Manual Instrukcja Użytkownika
(502 strony)
(502 strony)
Ekwipunek Rockwell-automation 2707-L8PxX, -L40PxX, -V40PxX DTAM Plus Operator In Instrukcja Użytkownika
(20 strony)
(20 strony)
(40 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji