Rockwell-automation AutoMax R-Net Processor Module Instrukcja Użytkownika Strona 1

     

2Ć2The resulting number indicates one of the following fault conditions:ă1 Ć EPROM checksum erroră2 Ć Scratchpad RAM failureă3 Ć Dual port memory fail

2Ć32.2 Electrical DescriptionNetwork operation is controlled by a Motorola 68010 CPU/directmemory access (DMA)/serial I/O architecture. 16K bytes of d

fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd

3Ć13.0 INSTALLATIONThis section describes how to install and replace the AutoMax RĆNetProcessor module. For more information regarding the RĆNetnetwor

3Ć23.1 WiringThe installation of wiring should conform to all applicable codes. Toreduce the possibility of noise interfering with the control system,

3Ć3Step 8. Turn on power to the rack. An internal diagnostic routine isautomatically executed by the module. If an error isencountered, the pattern of

fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd

4Ć14.0 PROGRAMMINGThis section describes how the data is organized in the AutoMaxRĆNet Processor module and provides examples of how the moduleis acce

4Ć2Register Function0 Reserved for System Use1 Reserved for System Use2 Reserved for System Use3 Reserved for System Use4 Drops On Line Status Bit 15Ć

4Ć34.1.1.3 Register 13 (Slot Number)Register 13 indicates the slot location of the AutoMax RĆNetProcessor module.4.1.1.4 Register 14 (Messages Receive

E Copyright Reliance Electric Industrial Company 1991.MultibusR is a registered trademark of Intel Corporation.AutoMaxt, RĆNett and ReSourcet are trad

4Ć4this register should be set to the highest number node that is on thesystem plus 1. Nodes on the network should be numberedconsecutively to avoid u

4Ć5AutoMax/DCS 5000 variables are mapped to the AutoMate imagearea during configuration and can be accessed by any task in anyAutoMax/DCS 5000 Process

4Ć671.0071.0171.0271.0371.0471.0571.0671.0771.1071.1171.1271.1371.1471.1571.1671.1772.0072.0172.0272.03..72.1672.1773.0073.01...73.1673.1774.0074.017

4Ć7When enabled by the Transmit Global Data Enabling Registers(registers 50Ć53), the individual points within these registers arebroadcast to all othe

4Ć84.1.3 Command Buffer AreaThe command buffers in the dual port memory are used to store thecommands for the AutoMax RĆNet Processor module that areg

4Ć94.2.3 Read RegisterThe Read Register command (003) is used to read data in up to 120sequential registers. When initiated by the GATEWAY_CMD_OK@func

4Ć104.4 ConfigurationBefore running any application tasks, the system must be configured.The major function of configuration is to assign meaningful s

4Ć11returned status will contain an error code. Refer to figure 4.6 for errorcodes returned by the GATEWAY_CMD_OK@ function. 00 =

4Ć124.6 Sample Application ProgramThe following application program example illustrates the use of theGATEWAY_CMD_OK@ function to initiate a Read Poin

5Ć15.0 DIAGNOSTICS ANDTROUBLESHOOTINGThis section describes how to troubleshoot the AutoMax RĆNetProcessor module. If the problem cannot be corrected

ITable of Contents1.0 Introduction 1Ć1...1.1 Additional Information 1Ć1...

5Ć25.3 Communication Line FailureProblem: The top and/or bottom red LEDs on the module faceplateflash on and off. This indicates a CRC error or lost t

AĆ1Appendix ATechnical SpecificationsAmbient ConditionsD Storage temperature: -40_Cto85_CD Operating temperature: 0_Cto55_CD Humidity: 5 Ć 90%, nonĆco

fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd

BĆ1Appendix BModule Block DiagramADDRESSDECODEWATCHDOGTIMERLEDDISPLAY2 ROTARYSWITCHESMULTIBUSEXCHANGELOGICDUAL PORTARBITRATIONLOGIC ANDCONTROL68010CPU

fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd

CĆ1   The following error codes are displayed (using a pattern of COM ER LEDs) whilethe AutoMax RĆNet Processor modul

fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd

Appendix DNode Number Conversion Chart                     

fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd

%Appendix ERĆNet Network SpecificationsNetwork OrganizationD  %"% Media Access ProtocolD  !!Physical ConfigurationD #!Maximum

  !  $5.0 Diagnostics And Troubleshooting 5Ć1... " 

fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd

fafadfdfdasfdsfdsdsdfdsfdsfdsfsdfdsaafdfdsfdsfdfdsfdsfsadfdaasfdfaddfdd

For additional information1 Allen-Bradley DriveMayfield Heights, Ohio 44124 USATel: (800) 241-2886 or (440) 646-3599http://www.reliance.com/automaxCop

    $ !   $

  &%/,#  2 /.*0 2#. ,*!#--*, *"/'# !#+'.# 2&%/,#  2 /' *,. #(*,1 #%&a

1Ć11.0 INTRODUCTIONThe products described in this instruction manual are manufacturedby RelianceR Electric Industrial Company.The AutoMax RĆNet Proces

1Ć2D JĆ3684 ReSource AutoMax PROGRAMMING EXECUTIVEINSTRUCTION MANUAL VERSION 2.0D JĆ3750 ReSource AutoMax PROGRAMMING EXECUTIVEINSTRUCTION MANUAL VERS

2Ć12.0 MECHANICAL/ELECTRICALDESCRIPTIONThis section describes the mechanical and electrical characteristics ofthe AutoMax RĆNet Processor module.2.1 M