Rockwell-automation 20D PowerFlex 700S with Phase I Control Reference Instrukcja Użytkownika Strona 10
- Strona / 190
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
10 Rockwell Automation Publication PFLEX-RM002D-EN-E - August 2013
Table of Contents
Zero Torque Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Absolute Min Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Start Inhibits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Start/Stop Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Configuring the Start and Stop for 3-Wire Control (Momentary Start
and Stop) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Configuring the Start and Stop for 2-Wire Control (Maintained Start
and Stop) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Start-Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Stop Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
SynchLink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
SynchLink Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
SynchLink Direct Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Multiply Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Buffered Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Speed Synchronization Example:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Master PowerFlex 700S Drive Setup (Transmitting Drive) . . . . . . 168
Follower PowerFlex 700S Setup (Receiving Drive) . . . . . . . . . . . . . 171
Sync Generator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Configuration: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Thermal Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Torque Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Torque Reference Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Unbalanced or Ungrounded Distribution Systems . . . . . . . . . . . . . . . . . 176
Unbalanced Distribution Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Ungrounded Distribution Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
User Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Peak Detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Selector Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Time Axis Generator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Limit Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
Voltage Class. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
Watts Loss. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Appendix A
History of Changes
PFLEX-RM002C-EN-E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Index
- Reference Manual 1
- Important User Information 2
- Summary of Changes 3
- New and Updated 3
- Information 3
- Table of Contents 5
- Appendix A 10
- History of Changes 10
- Additional Resources 11
- Chapter 1 13
- Accel Time 13
- Analog Inputs 14
- Analog Outputs 15
- Analog Output Configuration 16
- Auto/Manual 17
- Autotune 17
- Motor Control 18
- Motor Data 18
- Feedback Configuration 18
- Power Circuit Test 18
- Direction Test 19
- Motor Tests 19
- Auxiliary Power Supply 20
- Bus Regulation/Braking 20
- Cable, Control 24
- Cable, Motor Lengths 24
- Cable, Power 24
- Cable Trays and Conduit 24
- Carrier (PWM) Frequency 25
- CE Conformity 26
- Common Bus Systems 26
- Communication 26
- ControlNet (20-COMM-C) 26
- ControlLogix Programming 31
- Explicit Messaging 32
- Copy Cat 33
- Current Limit 33
- Datalinks 34
- Example Configuration 2: 35
- “Data Out” Parameters 35
- Example Configuration 3: 35
- Example Configuration 4: 35
- Decel Time 36
- DeviceNet (20-COMM-D) 36
- ControlLogix 37
- Digital Inputs 42
- SyncLink 43
- Configuration Example 45
- Digital Input Status Bits 45
- Digital Outputs 46
- Reference 47
- Drive Overload 48
- 150% * 3 s + 100%*57 s 49
- Drive Overtemperature 50
- (Frame 9 Only) 50
- Drive Peripheral Interface 50
- Peer-to-Peer Operation 51
- DriveLogix 52
- Dynamic Braking 53
- Efficiency 53
- Electronic Gearing 53
- Application Example: 54
- Key Words 54
- Nomenclature: 54
- Low Pass Filter 55
- Second Order Low Pass Filter 55
- Lead-Lag Filter 56
- Lead-Lag Filter “Lead” 57
- Notch Filter 59
- Figure 20 - Resonance 60
- Figure 21 - 10 Hz Notch 61
- Conclusion 61
- Flying Start 62
- Preset Frequency Search 63
- Hysteresis 65
- Number of 65
- Time Stops 65
- Grounding, General 66
- HIM Memory 66
- HIM Operations 66
- Inertia Adaptation 67
- Using the HIM 70
- Using DriveExecutive 71
- Motor Control Mode 72
- Motor Nameplate 73
- Motor Overload 73
- High Overload 74
- Motor Start/Stop Precautions 75
- Mounting 75
- Output Devices 76
- Output Display 76
- Overspeed Limit 77
- Permanent Magnet Motors 79
- Position Loop - Follower 82
- (Electronic Gearing) 82
- Speed Reference Selection 83
- Speed Reference Ramp 83
- Enabling the Position Loop 84
- Position Reference Selection 84
- Position Offset 85
- Position Loop Output Limits 86
- Tuning Tips 86
- Position Loop - In Position 87
- Overview 88
- Position Reference Scaling 89
- BW] Reg [Speed 91
- Gain]Filt [Strim2 91
- BW]Filt [SpdTrim2 91
- Position Loop - Position 92
- Position Loop - Registration 94
- Power Loss/Ride Through 95
- Ride Through Operation 97
- Ride Through Configuration 97
- Ride Through Timeout Fault 98
- Precharge Operation 98
- Precharge Timeout Fault 100
- External Precharge 101
- Precharge Staging 101
- Process PI Loop 102
- Process PI Regulator 103
- Process PI Limits 103
- Pulse Elimination Technique 104
- Reflected Wave 104
- Time (μsec) 105
- Remote I/O Adapter 106
- (20-COMM-R) 106
- Adapter PowerFlex 700S 107
- Datalink Programming 111
- Example: 112
- SLC/PLC-5 System 114
- Copy File 117
- Source #N13:112 117
- 1 117
- Source #F12:6 118
- #F13:12 118
- 2 118
- RFI Filter Grounding 119
- Speed Control, Speed Mode 119
- Speed Regulation 119
- Speed PI Regulator 120
- Autotune Speed Reference 121
- Speed Reference Limits 122
- Current Limit Stop 122
- Speed Error 122
- Servo Lock 123
- Speed Regulation Anti-Backup 123
- Proportional Gain 124
- Integral Gain 124
- Speed Regulator Output Limits 126
- Speed Regulator Output Filter 126
- Speed Regulator Tuning 127
- •ft. Tacc can be 129
- Speed Reference 130
- Speed Reference Scaling 131
- Speed Reference Select 132
- Jog Reference 133
- Stop Command 133
- Speed Limits 133
- Accel/Decel Ramp and S-Curve 134
- Inertia Compensation 135
- Friction Compensation 135
- Virtual Encoder 135
- Speed Reference Filter 136
- Speed Reference Scale 136
- Speed/Position Feedback 137
- Encoder 0 141
- Processing 141
- Sensorless 142
- Motor Simulator 142
- Feedback Option Cards 143
- Bit 3 2 Resolution Setting 145
- Motor Position Feedback 147
- Speed/Torque Select 152
- Torque Regulation Mode 153
- Min Mode / Max Mode 154
- Sum Mode 154
- Start Inhibits 155
- Start/Stop Modes 156
- Start-Up 160
- Stop Modes 160
- SynchLink 160
- SynchLink Direct Data 161
- Multiply Block 162
- Buffered Data 163
- Direct Data 165
- Int Real 166
- 64 Parameters 166
- 9. Click the Link Data tab 170
- 11. Click OK 170
- Cycle Power 173
- Sync Generator 174
- Test Points 174
- Thermal Regulator 175
- Torque Reference 175
- Unbalanced or Ungrounded 176
- Distribution Systems 176
- User Functions 177
- Two Position Dint Switch 178
- Configuration: 178
- Voltage Class 180
- Watts Loss 181
- Appendix A History of Changes 184
- Rockwell Automation Support 190
- Documentation Feedback 190
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 20D PowerFlex 700S with Phase I Control Reference
Ekwipunek Rockwell-automation T80017 Application Note Regent to Trusted Migratio Instrukcja Użytkownika
(23 strony)
(23 strony)
Ekwipunek Rockwell-automation T3834 ICS Regent Continuous Control Package for Wi Instrukcja Użytkownika
(23 strony)
(23 strony)
Ekwipunek Rockwell-automation Emonitor with a Gupta Multi-User Database Instrukcja Użytkownika
(50 strony)
(50 strony)
Ekwipunek Rockwell-automation MDO16FNS 16-Channel Digital Output Module 120Vac/d Instrukcja Użytkownika
(15 strony)
(15 strony)
Ekwipunek Rockwell-automation T8297 Trusted Output Power Distribution Unit (Diod Instrukcja Użytkownika
(10 strony)
(10 strony)
Ekwipunek Rockwell-automation FactoryTalk Alarms and Events Quick Start Instrukcja Użytkownika
(246 strony)
(246 strony)
Ekwipunek Rockwell-automation T8472 Trusted TMR 120V ac Isolated Output Module Instrukcja Użytkownika
(28 strony)
(28 strony)
Ekwipunek Rockwell-automation AADvance Controller Solutions Handbook Instrukcja Użytkownika
(148 strony)
(148 strony)
Ekwipunek Rockwell-automation Isomag 4 Universal Guard Safety Switch Instrukcja Użytkownika
(2 strony)
(2 strony)
(8 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.106 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji