Rockwell-automation 5730 DriveLogix5730 Controller for PowerFlex 700S Instrukcja Użytkownika Strona 192
- Strona / 217
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
A-4 DriveLogix5730 Controller Specifications
Indicator: Color: Description:
RUN off The controller is in Program or Test mode.
solid green The controller is in Run mode.
FORCE off No tags contain I/O force values.
I/O forces are inactive (disabled).
solid amber I/O forces are active (enabled).
I/O force values may or may not exist.
flashing amber One or more input or output addresses have been forced to an On or Off
state, but the forces have not been enabled.
BAT off The battery supports memory.
solid red Either the battery is:
not installed.
95% discharged and should be replaced.
I/O off Either:
There are no devices in the I/O configuration of the controller.
The controller does not contain a project (controller memory is empty).
solid green The controller is communicating with all the devices in its I/O configuration.
flashing green One or more devices in the I/O configuration of the controller are not
responding.
flashing red The controller is not communicating to any devices.
The controller is faulted.
COM off No RS-232 activity.
flashing green RS-232 activity.
OK off No power is applied.
flashing red If the controller is:
a new controller
not a new controller
Then:
the controller requires a firmware update
A major fault occurred.
To clear the fault, either:
- Turn the key switch from PROG to RUN to PROG
- Go online with RSLogix 5000 software
solid red The controller detected a non-recoverable fault, so it cleared the project
from memory. To recover:
Cycle power to the chassis.
Download the project.
Change to Run mode.
If the OK LED remains solid red, contact your Rockwell Automation
representative or local distributor.
solid green Controller is OK.
flashing green The controller is storing or loading a project to or from nonvolatile memory.
- DriveLogix™ 5730 1
- Controller 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- Configuring DriveLogix Motion 6
- Appendix B Access Procedures 7
- Overview 9
- Related Documentation 10
- Contacting Tech Support 10
- Controller Firmware 11
- Revision 11
- General Precautions 11
- What is DriveLogix5730? 13
- Loading Controller 14
- Firmware 14
- What is DriveLogix5730? 1-3 15
- 1-4 What is DriveLogix5730? 16
- Using CompactFlash 17
- 40012.eps 18
- What is DriveLogix5730? 1-7 19
- 030252015105 454035 50 656055 20
- Overhead Percentage 21
- Selecting a System 21
- Understanding the Virtual 24
- Backplane 24
- Chapter 2 25
- Determining When the 26
- Controller Updates the Drive 26
- Placing and Configuring the 27
- Electronic Keying 28
- Communication Formats 29
- “drive_module” 30
- Inhibiting the Drive 35
- Connection 35
- Using DriveExecutive Lite 36
- 3. Select the Power tab 37
- 6. Select the Setup tab 38
- Mode Change 41
- 5. Click the Apply button 44
- Accessing Drive Data 45
- Monitoring Drive Data 45
- Configuring the Controller’s 46
- Response to a Connection 46
- Monitoring the drive module 47
- Recommended 49
- Programming Techniques 49
- Chapter 3 51
- 20D-DL2-CL3 52
- 20D-DL2-CR3 52
- Validating I/O Layout 53
- Estimating RPI 54
- Controller Updates I/O 54
- Configuring the 55
- CompactBus 55
- Configuring Local I/O 57
- GSV ladder.tif 61
- Accessing I/O Data 62
- Example: 63
- Direct Connections for I/O 64
- Monitoring I/O Modules 65
- 27 19 11 66
- Configuring I/O Modules 67
- Using the Generic 67
- 1769-MODULE 67
- Programming the Controller 72
- Forward 83
- Reverse 83
- Launching DriveExecutive 84
- Then click Apply 85
- Configuring the Drive with 86
- DriveExecutive Software 86
- Downloading the Settings 90
- Additional Testing and 90
- Programming is Necessary 90
- Supported Motion 91
- Commands 91
- Chapter 5 93
- Configuring the Hardware 94
- Example 1: Workstation 98
- Directly Connected to a 98
- DriveLogix Controller 98
- Example 2: Workstation 99
- Remotely Connected to a 99
- Example 3: DriveLogix 102
- Controller to a Bar Code 102
- Configuring User Mode 104
- Chapter 6 105
- EtherNet/IP 106
- Controller Connections 115
- Over EtherNet/IP 115
- Configuring Distributed I/O 116
- Accessing Distributed I/O 117
- Adding a Remote Controller 119
- Producing and Consuming 119
- Producing a tag 121
- Consuming a Tag 122
- Sending Messages 123
- Mapping Addresses 126
- Using a MSG Instruction to 128
- Send an Email 128
- Creating String Tags 129
- Entering String Data 129
- Entering Ladder Logic 130
- Example 1: DriveLogix5730 135
- Controller and 135
- Distributed I/O 135
- Example 2: Controller to 136
- Sending a MSG instruction 138
- Receiving a MSG Instruction 139
- Chapter 7 141
- Configuration folder 143
- Scheduling the ControlNet 147
- If you have this software 150
- Then you can cache: 150
- Producing a Tag 156
- Guidelines for Configuring 157
- Connections 157
- Example 1: DriveLogix 158
- Controller and Remote I/O 158
- Example 2: DriveLogix5730 159
- Controller to 159
- DriveLogix5730 Controller 159
- Controller to Other Devices 162
- Chapter 8 167
- Example: Controlling I/O 168
- Over DeviceNet 168
- Module Command Array 174
- CompactBus: 176
- Entering Program Logic 178
- Chapter 9 179
- Configuring Your System for 180
- Planning a DH-485 Network 182
- Network Initialization 183
- Installing a DH-485 Network 184
- Browsing a DH-485 Network 187
- Remotely 187
- Appendix A 189
- DriveLogix5730 190
- Certifications 190
- Real-Time Clock Accuracy 190
- Controller LEDs 191
- CompactFlash card LED 193
- Embedded EtherNet/IP 194
- Option LEDs 194
- Network Status (NS) indicator 195
- Link Status (LNK) indicator 195
- Battery Life 196
- Appendix B 197
- Removing the Outside 199
- Removing the Inside Cover 199
- Connecting the Battery 200
- Replacing the Battery 201
- Installing the Embedded 203
- EtherNet/IP Option Board 203
- Installing the 203
- DriveLogix5730 Expansion 203
- Installing the Compact I/O 204
- Communications 205
- Daughtercard 205
- B-10 Access Procedures 206
- Application Restrictions 207
- Hold Last State and 209
- User-Defined Safe State Not 209
- Supported 209
- C-4 Application Restrictions 210
- Numerics 211
- Allen-Bradley 217
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 5730 DriveLogix5730 Controller for PowerFlex 700S
Ekwipunek Rockwell-automation 42KA Subminiature Flat Pack PHOTOSWITCH Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Rockwell-automation 23P PowerFlex DC Stand-Alone Regulator (SAR) Field Instrukcja Użytkownika
(10 strony)
(10 strony)
Ekwipunek Rockwell-automation 22-COMM-P PowerFlex Profibus Adapter Instrukcja Użytkownika
(116 strony)
(116 strony)
Ekwipunek Rockwell-automation 20M LPM15 Liquid-Cooled Adjustable Frequency AC Dr Instrukcja Użytkownika
(148 strony)
(148 strony)
Ekwipunek Rockwell-automation 140G-K-PB3L_PB4L_PB3H_PB4H Phase Barriers Instrukcja Użytkownika
(2 strony)
(2 strony)
Ekwipunek Rockwell-automation 20B PowerFlex 700 Drives - Frame 10 Components Rep Instrukcja Użytkownika
(88 strony)
(88 strony)
Ekwipunek Rockwell-automation 100 Contactors with 3-terminal DC Coil Instrukcja Użytkownika
(1 strony)
(1 strony)
Ekwipunek Rockwell-automation 23P PowerFlex DC Stand-Alone Regulator (SAR) In-Ru Instrukcja Użytkownika
(10 strony)
(10 strony)
Ekwipunek Rockwell-automation 20P PowerFlex DC Drive - Frame B AC Current Transd Instrukcja Użytkownika
(14 strony)
(14 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji