Rockwell-automation 6012DB PowerFlex Medium Voltage Variable Frequency Instrukcja Użytkownika Strona 92
- Strona / 138
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
92 Rockwell Automation Publication 6000-UM001B-EN-P - October 2014
Chapter 5 Preventative Maintenance and Component Replacement
3. Remove the Output Copper Bars that connect adjacent Power Modules
(Figure 31
).
If the Power Module is at the end of a row, remove the VSB and Motor
cable instead of an output copper bus.
4. Disconnect the fiber optic cables.
Figure 31 - Close up of Fiber Optic Location and Power Cables
5. Carefully withdraw the Power Module.
6. Install the new Power Module in reverse order of removal.
ATTENTION: When removing the fiber optic cables, be careful to prevent the
cables from straining or crimping as the resulting loss in light transmission will
impact performance.
ATTENTION: Minimum bend radius permitted for the fiber optic cables is 50
mm (2.0 in.). Any bends with a shorter inside radius can permanently damage
the fiber-optic cable.
Motor Cable
VSB Cable
Output Copper Bar
Fiber Optic Cables
- User Manual 1
- Important User Information 2
- Table of Contents 3
- Chapter 4 4
- Parameters and Function Codes 4
- Chapter 5 4
- Preventative Maintenance and 4
- Component Replacement 4
- Appendix D 6
- Appendix E 6
- Introduction 7
- Who Should Use This Manual 7
- What Is Not in This Manual 7
- Additional Resources 7
- General Precautions 8
- Service and Support 8
- Environmental Conditions 10
- How it Works 10
- Simplified Electrical 12
- Diagrams 12
- Standards Compliance 15
- Drive System Layout 17
- Isolation Transformer 18
- Drive System Layout Chapter 2 21
- Chapter 2 Drive System Layout 22
- Door Position Limit Switch 23
- Voltage Sensing Board 24
- Power Module Cabinet 25
- Power Modules 26
- Control Unit (all modules) 30
- Figure 22 - PLC Location 32
- Setup and Operation 33
- Status Indicators 34
- Main Interface Controls 35
- Set Frequency (Hz) 36
- Drive Operation Controls 37
- View Version Information 38
- Active Alarms Controls 39
- Reset Status 39
- Alarm History 40
- Chapter 3 Setup and Operation 42
- Operation 43
- Manual Bypass Cabinet 44
- Automatic Bypass Cabinet 44
- Choose Local/Remote Operation 45
- Open/Close Bypass Contactors 47
- Settings 48
- 4. Press to accept 49
- User Settings 50
- Change User Parameters 50
- Setup Settings 53
- View/Change P or T Parameters 53
- Restore “P” or “T” Parameters 55
- 0 ON -100 199.99 59
- 0 ON -100 100 60
- T Parameters 63
- Alarm List 64
- Daily Inspection 78
- Regular Maintenance Intervals 78
- Physical Checks (No Medium 79
- Voltage or Control Power) 79
- Final Report 80
- Fan Balance 84
- Inspect Isolation Transformer 86
- Inspect Voltage Sensing Board 87
- Replace Voltage Sensing Board 87
- Replace Power Module 91
- Replace Drawout Power Module 93
- Recessed Lifting Handles 94
- Mounting Rail 94
- Finger Assemblies 94
- Install Drawout Power Modules 95
- Replace Power Module Fuses 97
- Drawout Power Module 98
- Inspect or Replace HECS 99
- M5 x 12 Nut 100
- LV Control Cabinet 101
- Replace AC/DC Power Supplies 102
- G3 Power Supply 103
- Inspect UPS 104
- Replace UPS 105
- Replace UPS Batteries 106
- Inspect PLC 108
- Only remove the board using 110
- Inspect the HMI 111
- Replace the HMI 111
- Replace LV Control Relays 113
- Inspect Coils 116
- Inspect Contacts 116
- Inspect Pilot Lights 116
- Connections 117
- Review Firmware and Hardware 118
- Inspect/Review Spare Parts 118
- Technical Specifications 119
- Catalog Number Explanation 121
- Appendix C 123
- PowerFlex 6000 123
- Maintenance Schedule 123
- Spare Parts 127
- Torque Requirements 129
- Rockwell Automation Support 138
- Documentation Feedback 138
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 6012DB PowerFlex Medium Voltage Variable Frequency
Ekwipunek Rockwell-automation 6180 Processor Board (for 6180 Industrial Computer Instrukcja Użytkownika
(39 strony)
(39 strony)
Ekwipunek Rockwell-automation AK DBU - Dynamic Braking Unit 600/690 VAC Instrukcja Użytkownika
(56 strony)
(56 strony)
Ekwipunek Rockwell-automation 2361 Snubber Assembly Replacement (T-Frame) Instrukcja Użytkownika
(6 strony)
(6 strony)
Ekwipunek Rockwell-automation 2100 MCC NEMA Type 12 Sealing Instructions Instrukcja Użytkownika
(1 strony)
(1 strony)
Ekwipunek Rockwell-automation 2085-IRT4 Micro800 4-channel Thermocouple/RTD Inpu Instrukcja Użytkownika
(12 strony)
(12 strony)
Ekwipunek Rockwell-automation 8510 AC Spindle Drive System Programming Manual Instrukcja Użytkownika
(47 strony)
(47 strony)
Ekwipunek Rockwell-automation 5370-CBPK Color CVIM BLISTER-PAK Option Instrukcja Użytkownika
(84 strony)
(84 strony)
Ekwipunek Rockwell-automation 2361 Gate Interface Board Replacement Instrukcja Użytkownika
(6 strony)
(6 strony)
Ekwipunek Rockwell-automation 6181 CPU Upgrade for 6181 Industrial Computers Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Rockwell-automation 2100 CENTERLINE Bolted Pressure Contact Switch Instrukcja Użytkownika
(12 strony)
(12 strony)
Ekwipunek Rockwell-automation 2361 Tachometer Feedback Board Replacement Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Rockwell-automation 8520 9/Series CNC Integration Maintenance Manual D Instrukcja Użytkownika
(898 strony)
(898 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji