Rockwell-automation 1305 AC Drive, Firmware 1.01-3.00 User Manual Instrukcja Użytkownika Strona 127
- Strona / 162
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Chapter 6 –Troubleshooting and Fault Information
6-7
Table 6.B Bulletin 1305 Fault Descriptions (cont.)
Fault Name & Number Fault Description Action to Take
Pin ID Error Communication Hardware problem. 1. Unplug the HIM from the cable or drive and re-connect.
2. Replace Communication Cable.
Phase U Fault
8
A phase to ground fault has been detected between the drive
d r hs ph se
Check the wiring between the drive and motor. Check motor for
gr u ded ph se
P
h
a
s
e
U F
a
u
l
t
F38
A
ph
a
se
to
gr
o
u
n
d
fa
u
lt
h
a
s
b
ee
n
de
t
e
ct
ed
b
e
tw
ee
n t
he
dr
i
ve
and motor in this phase.
Che
ck t
he
wi
r
in
g
b
e
tw
ee
n t
he
dr
i
ve
an
d
moto
r
.
Che
ck moto
r
fo
r
grounded phase.
Phase V Fault
F39
A phase to ground fault has been detected between the drive
and motor in this phase.
Check the wiring between the drive and motor. Check motor for
grounded phase.
Phase W Fault
F40
A phase to ground fault has been detected between the drive
and motor in this phase.
Check the wiring between the drive and motor. Check motor for
grounded phase.
Power Loss Fault
F3
DC bus voltage remained below 85% of nominal for longer than
0.500 sec. [Line Loss Fault] parameter is programmed to “F03
Enable”.
Monitor the incoming AC line for low voltage or line power
interruption.
Power Mode Fault
F26
Internal error. Reset drive to factory defaults.
Power Test Fault
F46
Fault detected during initial start-up sequence. Check drive wiring. Check motor wiring. Reset drive to factory
defaults.
Reprogram Fault
F48
Occurs when drive parameters are reset to defaults. Clear fault.
Run Boost Fault
F34
An attempt has been made to set the [Run Boost] parameter to
a value greater than the [Start Boost] parameter.
Verify that parameter has been programmed correctly.
- User Manual 1
- Important User Information 2
- Document Update 3
- Summary of Changes 5
- Chapter 4 – Start-Up 8
- Chapter 5 – Programming 8
- Appendix C – Accessories 9
- Table of Contents 10
- Information and Precautions 11
- GENERAL PRECAUTIONS 12
- NAMEPLATE LOCATION 14
- FIRMWARE COMPATIBILITY 14
- Output ➀➁ 16
- Current (A) 16
- Installation/Wiring 17
- TERMINAL BLOCK ACCESS 19
- INPUT DEVICES 21
- INPUT POWER CONDITIONING 22
- INPUT FUSING 22
- RFI FILTERING 24
- GROUNDING 25
- POWER WIRING 27
- DRIVE OPERATION WITHOUT A 31
- HUMAN INTERFACE MODULE (HIM) 31
- CONTROL WIRING 31
- See notes on page 2-18 33
- OUTPUT DEVICES 35
- CABLE TERMINATION 35
- ADAPTERS 36
- Human Interface Module 39
- HIM REMOVAL AND INSTALLATION 42
- HIM MODES 43
- PROGRAM AND DISPLAY MODES 45
- Logic Mask 46
- X1111111 46
- Choose Group 46
- PROCESS MODE 47
- EEPROM MODE 48
- EEPROM MODE (cont.) 49
- SEARCH MODE 51
- CONTROL STATUS MODE 52
- CONTROL STATUS MODE (cont.) 53
- PASSWORD MODE 54
- PASSWORD MODE (cont.) 55
- Start-Up 59
- Chapter 4 –Start–Up 60
- DESCRIPTION 60
- HIM DISPLAY 60
- Reset Factory Defaults 61
- [Input Mode] Selection 61
- Open Enable Signal 64
- Restore Enable Signal 64
- Remove ALL Power 66
- Reconnect Motor 66
- Slowly Increase Speed 68
- Programming 69
- PROGRAMMING EXAMPLE 72
- Metering 73
- Metering Group (cont.) 74
- Set Up Group (cont.) 77
- Advanced Setup 82
- Advanced Set Up Group (cont.) 83
- Frequency 91
- Frequency Set Group (cont.) 92
- “French” 99
- “Italian” 99
- “Japanese” 99
- “Spanish” 99
- “German” 99
- Feature Select Group (cont.) 100
- 0 to [Maximum Freq] 102
- 815V/460V Drives 102
- Chapter 5 –Programming 103
- Cycling Input Power 104
- Diagnostics Group (cont.) 106
- Saves parameter Ram to EEPROM 109
- Masks Group (cont.) 111
- Controlling 114
- Not Controlling 114
- Owners Group (cont.) 115
- Adapter I/O 117
- Adapter I/O Group (cont.) 118
- Process Display 119
- Linear List 120
- CHAPTER OBJECTIVES 121
- FAULT INFORMATION 121
- Table 6.C Troubleshooting 129
- Appendix A – 133
- Appendix B – 139
- Appendix C – 155
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 1305 AC Drive, Firmware 1.01-3.00 User Manual
Ekwipunek Rockwell-automation 1502 400 Amp Medium Voltage Contactor (Series D) Instrukcja Użytkownika
(54 strony)
(54 strony)
Ekwipunek Rockwell-automation Logix5000 Program Parameters Programming Manual Instrukcja Użytkownika
(36 strony)
(36 strony)
Ekwipunek Rockwell-automation 1732D-XXXX PointBlock 16 dc Input Module Installat Instrukcja Użytkownika
(24 strony)
(24 strony)
Ekwipunek Rockwell-automation 1771-CFM Config. Flowmeter Installation Instructio Instrukcja Użytkownika
(20 strony)
(20 strony)
Ekwipunek Rockwell-automation 1738-AENTR, Series B POINT I/O and ArmorPOINT I/O Instrukcja Użytkownika
(120 strony)
(120 strony)
Ekwipunek Rockwell-automation 1769-OA8 Compact 100 to 240V ac Solid State Output Instrukcja Użytkownika
(20 strony)
(20 strony)
Ekwipunek Rockwell-automation 1734-PDN/B Point I/O DeviceNet Communication Inter Instrukcja Użytkownika
(20 strony)
(20 strony)
Ekwipunek Rockwell-automation 1786-RPFRXL ControlNet Fiber Ring Modules Installa Instrukcja Użytkownika
(40 strony)
(40 strony)
Ekwipunek Rockwell-automation 1732E-XXXX ArmorBlock 2-Port EtherNet/IP Modules w Instrukcja Użytkownika
(24 strony)
(24 strony)
Ekwipunek Rockwell-automation 1747-L55x,D174710.4 SLC 500 Ethernet Instrukcja Użytkownika
(70 strony)
(70 strony)
Ekwipunek Rockwell-automation 1769-ADN Compact I/O DeviceNet Adapter Instrukcja Użytkownika
(28 strony)
(28 strony)
Ekwipunek Rockwell-automation 1746-Px SLC 500 Power Supplies Installation Instru Instrukcja Użytkownika
(20 strony)
(20 strony)
Ekwipunek Rockwell-automation 1747-PCINT API Software for 1746 I/O Instrukcja Użytkownika
(155 strony)
(155 strony)
Ekwipunek Rockwell-automation 1746-NI16V SLC 500 Analog I/O Modules Instrukcja Użytkownika
(20 strony)
(20 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.134 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji