Rockwell-automation 150 USE MN/SMC DIALOG + CONTROLLER Instrukcja Użytkownika Strona 107
- Strona / 189
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Options
7-23
Figure 7.19 Typical Wiring Diagram for the Slow Speed with Braking Option
with an Isolation Contactor
①
Customer supplied.
②
Refer to the controller nameplate to verify the rating of the control power input voltage.
Note: Refer to Chapter 3 for typical power circuits.
Brake
➀
Stop
➀
IC
➀
Control Power
➁
Slow Speed
➀
Start
➀
11 12
13 14 15 16 17 18 19 20
21 22
23 24 25 26 27 28 29 30
Internal
Auxiliary
Contacts
Auxiliary contacts set
for Normal
SMC Dialog Plus
Control Terminals
- User Manual 1
- Please Read! 2
- Important User Information 2
- Table of Contents 3
- Table of Contents 10
- Product Overview 11
- Starting Modes 12
- Selectable Kickstart 13
- Current Limit Start 13
- Percent 14
- Voltage 14
- Time (seconds) 14
- Energy Saver 15
- Phase Rebalance 15
- Protection and 15
- Protection and Diagnostics 16
- Line Faults 19
- Underload 19
- Metering 20
- Communication 21
- Programming 21
- Status Indication 21
- Control Options 22
- Pump Control Option 23
- Preset Slow Speed Option 23
- Control Options (cont.) 24
- Accu-Stop 25
- Installation 27
- General Precautions 28
- Heat Dissipation 28
- Enclosures 28
- Ventilated Enclosures 29
- Non-ventilated Enclosures 29
- Mounting 30
- Mounting (cont.) 32
- Power Factor 35
- Correction Capacitors 35
- Current-limiting 36
- Fast Acting 36
- Protective Modules 37
- Motor Overload 37
- Protection 37
- Human Interface Module 38
- Human Interface 40
- Module (cont.) 40
- “Comm Fault” will occur 41
- Converter Modules 42
- Converter Modules (cont.) 44
- Electromagnetic 44
- Compatibility (EMC) 44
- Accessory Requirements 45
- Chapter 3 47
- Terminal Locations (cont.) 48
- Power Wiring 49
- Control Power 50
- Fan Power 51
- Control Terminal 52
- Designations 52
- Grounding 52
- Provision 52
- Standard Controller 53
- Wiring Diagrams 53
- Wiring Diagrams (cont.) 54
- Programming Menu (cont.) 66
- Password 69
- Parameter Management 70
- Using Parameter Management 71
- Parameter Modification 72
- Soft Start 73
- Dual Ramp Start 74
- Full Voltage Start 74
- Basic Setup 75
- Advanced Setup 76
- Example Settings 77
- Calibration 79
- Motor Data Entry (cont.) 80
- Calibration Procedure 81
- Calibration Procedure (cont.) 82
- Viewing Metering 84
- Data (cont.) 84
- Chapter 7 85
- Programming Parameters 87
- Control Wiring for 89
- SCANport Control 89
- Soft Stop, Pump Control, and 89
- Controller Interfacing 93
- Soft Stop Option 95
- Accu-Stop Options 98
- Contactor 100
- Preset Slow Speed and 102
- Accu-Stop Options (cont.) 102
- Preset Slow Speed 103
- Accu-Stop Option 104
- Customer supplied 105
- Serial Communications 110
- Control Enable 111
- SMC Status Data 112
- Reference/Feedback 112
- Parameter Listing 112
- Scale Factor 112
- Conversion 112
- Display Unit 113
- Equivalents 113
- Datalinks 113
- Interfacing 113
- Processing Time 113
- Remote I/O Examples 114
- Remote I/O Examples (cont.) 115
- G File Configuration 116
- I/O Addressing 116
- Block Transfer Instructions 130
- DeviceNet Examples 133
- I/O Mapping 134
- Refer To Table 8.A 137
- Explicit Messaging: 138
- Examples 140
- Sequence of Events: 140
- Setting Up the Data File: 141
- Example Ladder Logic Program: 142
- Diagnostics 144
- Clear Fault (cont.) 145
- Fault Buffer 145
- Fault Auxiliary Contact 145
- Fault Definitions 146
- Open Gate 148
- Excess Starts/Hour 148
- Controller Temp 148
- Comm Fault 148
- Troubleshooting 150
- Control Module Removal 155
- 180–360 Amp 156
- 500–1000 Amp 158
- Control Module Replacement 159
- Protective Cover Removal 159
- MOV Fuse 160
- Replacement 160
- Power Module and Interface 160
- Board Resistance Check 160
- 180-1000 Amp 162
- Specifications 164
- Refer to product nameplate 165
- Parameter Information 170
- Renewal Parts 176
- Accessories 180
- Glossary 181
- Glossary-2 182
- Glossary-3 183
- Glossary-4 184
- 40055-145-01(C) 189
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 150 USE MN/SMC DIALOG + CONTROLLER
(2 strony)
(4 strony)
(4 strony)
Ekwipunek Rockwell-automation 25B PowerFlex 520-Series Control & Power Modul Instrukcja Użytkownika
(2 strony)
(2 strony)
Ekwipunek Rockwell-automation 809S-E1A_E1D_E1ZJ Current Voltage Monitor Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Rockwell-automation 25B PowerFlex 520-Series Adjustable Frequency AC D Instrukcja Użytkownika
(36 strony)
(36 strony)
Ekwipunek Rockwell-automation 21G PowerFlex 755 Transition Section and Splicing Instrukcja Użytkownika
(26 strony)
(26 strony)
Ekwipunek Rockwell-automation 21G PowerFlex 750-Series Option Module Instrukcja Użytkownika
(2 strony)
(2 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.083 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji