Rockwell-automation 25-COMM-E2P PowerFlex 25-COMM-E2P Dual-Port EtherN Instrukcja Użytkownika Strona 141
- Strona / 172
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Rockwell Automation Publication 520COM-UM003A-EN-E - June 2013 141
EtherNet/IP Objects Appendix C
N41:0
N41:1
N41:2
N41:3
N41:4
N41:5
N41:6
N41:7
N41:8
N41:9
N41:10
Logic Command Word
Unused
Reference
Unused
Datalink From Net 1
Unused
Datalink From Net 2
Unused
Datalink From Net 3
Unused
Datalink From Net 4
Logic Status Word
Unused
Feedback
Unused
Datalink To Net 1
Unused
Datalink To Net 2
Unused
Datalink To Net 3
Unused
Datalink To Net 4
N42 This N-file lets you read and write some values configuring the port
N42:3 Time-out (read/write): Time (in seconds) allowed between messages to the N41 or N44 file. If the
adapter does not receive a message in the specified time, it performs the fault action configured in
parameter C143 [EN Comm Flt Action].
N42:7 Adapter Port Number (read only): DPI port on the drive to which the adapter is connected.
42:8 Peer Adapters (read only): Bit field of devices having DPI Peer capabilities.
N44 For Multi-drive mode Only
This N-file lets you read and write control I/O messages. You can write control I/O messages only when
all of the following conditions are true:
• The adapter is not receiving I/O from a scanner. For example, there is no scanner on the network,
the scanner is in idle (program) mode, the scanner is faulted, or the adapter is not mapped to the
scanner.
• The value of N42:3 is set to a non-zero value.
Write Read
N44:0
N44:1
N44:2
N44:3
N44:4
N44:5
N44:6
N44:7
N44:8
N44:9
N44:10
Drive 0 Logic Command
Unused
Drive 0 Reference
Drive 1 Logic Command
Drive 0 Reference
Drive 2 Logic Command
Drive 2 Reference
Drive 3 Logic Command
Drive 3 Reference
Drive 4 Logic Command
Drive 4 Reference
Drive 0 Logic Status
Unused
Drive 0 Feedback
Drive 1 Logic Status
Drive 1 Feedback
Drive 2 Logic Status
Drive 2 Feedback
Drive 3 Logic Status
Drive 3 Feedback
Drive 4 Logic Status
Drive 4 Feedback
N10...N18 These N-files lets you read and write parameter values in the drive and the adapter.
Single-Drive Mode Multi-Drive Mode
N10:0
N10:1...999
Number of parameters in the drive
Drive parameters 1...999
Number of parameters in Drive 0
Drive 0 parameters 1...999
N11:0...999 Drive parameters 1000...1999 Drive 0 parameters 1000...1999
N12:0...999 Drive parameters 2000...2999 Drive 0 parameters 2000...2999
N13:0 Number of parameters in this adapter Number of parameters in this adapter
N13:1...999 Parameters 1...999 in this adapter Parameters 1...999 in this adapter
N14:0 Number of parameters in the DSI device Number of parameters in Drive 1
N14:1...999 Parameters 1...999 in the DSI device Drive 1 parameters 1...999
N15:0 Number of parameters in this adapter Number of parameters in Drive 2
N15:1...999 Parameters 1...999 in this adapter Drive 2 parameters 1...999
N16:0 Not supported Number of parameters in Drive 3
N16:1...999 Not supported Drive 3 parameters 1...999
N17:0 Not supported Number of parameters in Drive 4
N17:1...999 Not supported Drive 4 parameters 1...999
N18:0 Not supported Number of parameters in this adapter
N18:1...999 Not supported Parameters 1...999 in this adapter
N-File Description
- User Manual 1
- Important User Information 2
- Table of Contents 3
- Overview 7
- Preface Overview 8
- Getting Started 9
- Features 10
- Understanding Parameter 10
- Compatible Products 11
- Required Equipment 11
- Safety Precautions 12
- Quick Start 13
- Chapter 1 Getting Started 14
- Installing the Adapter 15
- Setting the Node Address 16
- Connecting the Adapter to 18
- 00:00:BC:2E:69:F6 21
- Applying Power 22
- ENET LINK 23
- EtherNet/IP 23
- Commissioning the Adapter 24
- Configuring the Adapter 25
- Using the PowerFlex 4-Class 27
- HIM to Access Parameters 27
- Setting the Adapter Node 27
- Using a BOOTP or DHCP 28
- Using Adapter Parameters 31
- Setting the Data Rate 32
- Using Master-Slave Hierarchy 33
- Setting a Fault Action 34
- Changing the Fault Action 35
- Resetting the Adapter 36
- Restoring Adapter 36
- Parameters to Factory 36
- Defaults 36
- Viewing the Adapter Status 37
- Using Parameters 37
- Updating the Adapter 37
- Firmware 37
- Configuring the I/O 39
- CompactLogix Example 40
- Configuring the I/O Chapter 4 41
- Designer 42
- Chapter 4 Configuring the I/O 46
- Controller Input Tags 47
- Controller Output Tags 47
- Logix Designer 50
- ADC and Logix Memory 54
- Monitoring the ADC Progress 55
- Input Image Controller Tags 60
- Output Image Controller Tags 60
- Limitations in Using 62
- MicroLogix 1100/1400 62
- Using the I/O 63
- Understanding the I/O Image 64
- Using Logic Command/Status 65
- Using Reference/Feedback 65
- Using Datalinks 66
- Example Ladder Logic 67
- Program Information 67
- Feedback 68
- Reference 69
- Logix Designer Software 70
- Chapter 5 Using the I/O 72
- Using Explicit Messaging 73
- Explicit Messaging Process 74
- Using Multi-Drive Mode 87
- System Wiring 89
- Configuring the RS-485 91
- Using Multi-Drive Add-On 91
- Differences Found Screen 101
- Multi-Drive Ladder Logic 102
- Program for Generic Profile 102
- CompactLogix Controller 103
- Example Using Generic 103
- Main Routine 104
- Drive 0...4 Control Routines 105
- Drive 0 Control Routine 106
- Drive 1 Control Routine 107
- Drive 2 Control Routine 108
- Drive 3 Control Routine 109
- Drive 4 Control Routine 110
- Multi-Drive Mode Explicit 111
- Messaging 111
- Additional Information 112
- Troubleshooting 115
- PORT Status Indicator 116
- MOD Status Indicator 116
- NET A Status Indicator 116
- NET B Status Indicator 117
- Viewing Adapter Diagnostic 117
- Viewing and Clearing Events 120
- Adapter Events 121
- Specifications 123
- Appendix A Specifications 124
- Adapter Parameters 125
- EtherNet/IP Objects 129
- Identity Object 130
- Instance Attributes 131
- Assembly Object 132
- Register Object 133
- Instances (Multi-Drive) 134
- Class Attributes 135
- Parameter Object 136
- PCCC Object 139
- N-Files 140
- DPI Device Object 142
- DPI Parameter Object 145
- on page 150 147
- Descriptor Attributes 148
- Formulas for Converting 150
- Common Services 150
- Object Specific Services 150
- DPI Fault Object 151
- TCP/IP Interface Object 153
- Ethernet Link Object 155
- Appendix D 157
- Logic Command Word 157
- Logic Status Word 158
- Position Bit Definitions 159
- Glossary 161
- Rockwell Automation Support 172
- Documentation Feedback 172
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 25-COMM-E2P PowerFlex 25-COMM-E2P Dual-Port EtherN
Ekwipunek Rockwell-automation 21G 750-Series POD Remote Mounting Kit Instrukcja Użytkownika
(16 strony)
(16 strony)
Ekwipunek Rockwell-automation Atlas 5-GD2 Key Operating Instructions Instrukcja Użytkownika
(1 strony)
(1 strony)
Ekwipunek Rockwell-automation 193-ERR E1 PLUS Remote Reset Accessory Module Instrukcja Użytkownika
(8 strony)
(8 strony)
Ekwipunek Rockwell-automation 440T Prosafe Dual Key Rotary Key Switches Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Rockwell-automation 855T DeviceNet Stack Light User Manual Instrukcja Użytkownika
(72 strony)
(72 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.081 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji