Rockwell-automation 25-COMM-E2P PowerFlex 25-COMM-E2P Dual-Port EtherN Instrukcja Użytkownika Strona 64
- Strona / 172
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
64 Rockwell Automation Publication 520COM-UM003A-EN-E - June 2013
Chapter 5 Using the I/O
Understanding the I/O Image
The terms input and output are defined from the controller’s point of view.
Therefore, output I/O is data that is produced by the controller and consumed by
the adapter. Input I/O is data that is produced by the adapter and consumed as
input by the controller. The I/O image will vary based on:
• How many of the drive’s 16-bit Datalinks (Host parameters C161 [Opt
Data In 1] through C164 [Opt Data In 4] and C165 [Opt Data Out 1]
through C168 [Opt Data Out 4]) are used.
Device parameters 02 [DLs From Net Act] and 03 [DLs To Net Act]
must also be configured accordingly if Datalinks are used.
• ControlLogix/CompactLogix Controllers only—The drive Add-On
Profile (AOP) used in RSLogix 5000 (version 17 or greater) or Logix
Designer (version 21 or greater) software, or the Generic Profile (all
versions).
• If Multi-drive mode is enabled, and the number of daisy-chained drives
that are present.
I/O Controller Image
Since the drive Add-On Profile in RSLogix 5000 (version 17 or greater) and
Logix Designer (version 21 or greater) software provides descriptive controller
tags, the I/O image (tag size and location) is automatically configured based on
the drive being used. When using the Generic Profile in RSLogix 5000 or Logix
Designer, however, controller tags are not descriptive.
I/O Image for PowerFlex 525 Drives
on page 64 shows the I/O image when using
all of the 16-bit Datalinks.
I/O Image for PowerFlex 525 Drives
(16-bit Logic Command/Status, Reference/Feedback, and Datalinks)
Single drive mode is the typical configuration, where one node consists of a
PowerFlex 520-series drive with a 25-COMM-E2P adapter.
For Multi-Drive mode, where one node can consist of up to five drives, see Using
Multi-Drive Mode on page 87.
INT Output Input Using...
INT Drive Add-On Profile INT Generic Profile
0Logic Command0Logic Status 0Padword
1 Reference 1 Feedback 1 Padword
2 Datalink 1 2 Datalink 1 2 Logic Status
3 Datalink 2 3 Datalink 2 3 Feedback
4 Datalink 3 4 Datalink 3 4 Datalink 1
5 Datalink 4 5 Datalink 4 5 Datalink 2
6 Datalink 3
7 Datalink 4
- User Manual 1
- Important User Information 2
- Table of Contents 3
- Overview 7
- Preface Overview 8
- Getting Started 9
- Features 10
- Understanding Parameter 10
- Compatible Products 11
- Required Equipment 11
- Safety Precautions 12
- Quick Start 13
- Chapter 1 Getting Started 14
- Installing the Adapter 15
- Setting the Node Address 16
- Connecting the Adapter to 18
- 00:00:BC:2E:69:F6 21
- Applying Power 22
- ENET LINK 23
- EtherNet/IP 23
- Commissioning the Adapter 24
- Configuring the Adapter 25
- Using the PowerFlex 4-Class 27
- HIM to Access Parameters 27
- Setting the Adapter Node 27
- Using a BOOTP or DHCP 28
- Using Adapter Parameters 31
- Setting the Data Rate 32
- Using Master-Slave Hierarchy 33
- Setting a Fault Action 34
- Changing the Fault Action 35
- Resetting the Adapter 36
- Restoring Adapter 36
- Parameters to Factory 36
- Defaults 36
- Viewing the Adapter Status 37
- Using Parameters 37
- Updating the Adapter 37
- Firmware 37
- Configuring the I/O 39
- CompactLogix Example 40
- Configuring the I/O Chapter 4 41
- Designer 42
- Chapter 4 Configuring the I/O 46
- Controller Input Tags 47
- Controller Output Tags 47
- Logix Designer 50
- ADC and Logix Memory 54
- Monitoring the ADC Progress 55
- Input Image Controller Tags 60
- Output Image Controller Tags 60
- Limitations in Using 62
- MicroLogix 1100/1400 62
- Using the I/O 63
- Understanding the I/O Image 64
- Using Logic Command/Status 65
- Using Reference/Feedback 65
- Using Datalinks 66
- Example Ladder Logic 67
- Program Information 67
- Feedback 68
- Reference 69
- Logix Designer Software 70
- Chapter 5 Using the I/O 72
- Using Explicit Messaging 73
- Explicit Messaging Process 74
- Using Multi-Drive Mode 87
- System Wiring 89
- Configuring the RS-485 91
- Using Multi-Drive Add-On 91
- Differences Found Screen 101
- Multi-Drive Ladder Logic 102
- Program for Generic Profile 102
- CompactLogix Controller 103
- Example Using Generic 103
- Main Routine 104
- Drive 0...4 Control Routines 105
- Drive 0 Control Routine 106
- Drive 1 Control Routine 107
- Drive 2 Control Routine 108
- Drive 3 Control Routine 109
- Drive 4 Control Routine 110
- Multi-Drive Mode Explicit 111
- Messaging 111
- Additional Information 112
- Troubleshooting 115
- PORT Status Indicator 116
- MOD Status Indicator 116
- NET A Status Indicator 116
- NET B Status Indicator 117
- Viewing Adapter Diagnostic 117
- Viewing and Clearing Events 120
- Adapter Events 121
- Specifications 123
- Appendix A Specifications 124
- Adapter Parameters 125
- EtherNet/IP Objects 129
- Identity Object 130
- Instance Attributes 131
- Assembly Object 132
- Register Object 133
- Instances (Multi-Drive) 134
- Class Attributes 135
- Parameter Object 136
- PCCC Object 139
- N-Files 140
- DPI Device Object 142
- DPI Parameter Object 145
- on page 150 147
- Descriptor Attributes 148
- Formulas for Converting 150
- Common Services 150
- Object Specific Services 150
- DPI Fault Object 151
- TCP/IP Interface Object 153
- Ethernet Link Object 155
- Appendix D 157
- Logic Command Word 157
- Logic Status Word 158
- Position Bit Definitions 159
- Glossary 161
- Rockwell Automation Support 172
- Documentation Feedback 172
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 25-COMM-E2P PowerFlex 25-COMM-E2P Dual-Port EtherN
Ekwipunek Rockwell-automation 21G 750-Series POD Remote Mounting Kit Instrukcja Użytkownika
(16 strony)
(16 strony)
Ekwipunek Rockwell-automation Atlas 5-GD2 Key Operating Instructions Instrukcja Użytkownika
(1 strony)
(1 strony)
Ekwipunek Rockwell-automation 193-ERR E1 PLUS Remote Reset Accessory Module Instrukcja Użytkownika
(8 strony)
(8 strony)
Ekwipunek Rockwell-automation 440T Prosafe Dual Key Rotary Key Switches Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Rockwell-automation 855T DeviceNet Stack Light User Manual Instrukcja Użytkownika
(72 strony)
(72 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji