Rockwell-automation 1769-IF4FXOF2F Compact Combination Fast Analog I/O Instrukcja Użytkownika Strona 49
- Strona / 94
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Publication 1769-UM019A-EN-P - October 2008 49
Module Data, Status, and Channel Configuration Chapter 3
Alarm Deadbands
The module checks for an alarm deadband value that is less than 0 or
large enough to be equal to or exceed one-half of the difference
between the high alarm and low alarm values. When one of these
conditions occurs, a module configuration fault results.
Output Channel
Configuration
Each output channel is independently configured via a group of eight
consecutive words in the Configuration Data file. The first two words
of the group consist of bit fields, the settings of which determine how
the output channel operates. See the tables below and the
descriptions that follow for valid configuration settings and their
meanings. The default bit status of the configuration file is all zeros.
Low
High
Alarm Deadbands
Normal Input Range
High alarm turns OFF.
Low alarm turns OFF.
Low alarm turns ON.
High alarm turns ON.
Bit Definitions for Output Channel Configuration Words
Define To choose Make these bit settings
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
Program to Fault
Enable (PFE)
(1)
Program Data 1
Fault Data
0
Program Mode (PM)
(1)
User-defined 1
Hold Last State 0
Fault Mode (FM)
(1)
User-defined 1
Hold Last State 0
Enable Ramping (ER)
(1)
Enable 1
Disable 0
Latch Clamp Status
(LC)
Enable 1
Disable 0
Enable Low Clamp
Alarm Interrupt (ELI)
(2)
Enable 1
Disable 0
Enable Low Clamp
Alarm Interrupt (ELI)
(2)
Enable 1
Disable 0
Enable Channel (EC) Enable 1
Disable 0
(1) Alternate output states are not supported by all controllers. Refer to your controller’s user manual to determine whether alternate output states and this module function
are supported.
(2) Module interrupts are not supported by all controllers. Refer to your controller’s user manual to determine whether module interrupts are supported.
- Compact I/O Combination Fast 1
- Analog I/O Module 1
- Important User Information 2
- Table of Contents 3
- Chapter 4 4
- Module Diagnostics and 4
- Troubleshooting 4
- About This Publication 7
- Who Should Use This 7
- Publication 7
- Additional Resources 8
- Overview 9
- Chapter 1 Overview 10
- System Overview 11
- Module Operation 11
- Installation and Wiring 13
- ATTENTION 14
- Remove Power 15
- Reduce Noise 15
- Assemble the Compact I/O 16
- Mounting the Module 17
- Mount to a Panel 18
- Replace a Single Module 19
- Within a System 19
- Grounding the Module 20
- System Wiring Guidelines 21
- Voltage Output Accuracy 23
- Label the Terminals 24
- Remove the Finger-safe 25
- Terminal Block 25
- Wire the Finger-safe 25
- Wire the Modules 27
- Terminal Layout 28
- Wire Differential Inputs 29
- IMPORTANT 30
- Wiring Analog Outputs 31
- Configuration 33
- Module Addressing 34
- Output Image 35
- Configuration File 35
- Input Data File 36
- Output Data File 39
- Configuration Data File 40
- Input Channel 41
- Enable/Disable Channel (EC) 43
- Input Filter Selection 43
- Channel Step Response 44
- Input Type/Range Selection 45
- Input Data Selection Formats 45
- Real Time Sampling 46
- Time Stamping 47
- Process Alarms 48
- Alarm Deadband 48
- Output Channel 49
- Program Mode (PM) 50
- Program Value 51
- Fault Mode (FM) 51
- Fault Value 52
- Program to Fault Enable (PFE) 52
- Clamping (Limiting) 52
- Output Ramping 53
- Enable Ramping (ER) 54
- Ramp Rate 54
- Output Type/Range Selection 55
- Output Data Selection Formats 56
- Introduction 59
- Safety Considerations 59
- Power Cycle Diagnostics 60
- Channel Diagnostics 61
- Non-critical Versus Critical 61
- Module Errors 61
- Module Error Definition 62
- Error Codes 63
- Invalid Input Range Selected 64
- Invalid Input Format Selected 65
- Alarm Not Enabled 65
- Invalid Alarm Data 65
- Invalid Input Filter Selected 65
- Module Inhibit Function 67
- Contacting Rockwell 68
- Automation 68
- Specifications 69
- Input Specifications 70
- Output Specifications 71
- Certifications 72
- Replacement Parts 72
- MicroLogix 1500 Controller 73
- Module Output Image 74
- Module Configuration File 74
- Configure Analog I/O 75
- Modules in a MicroLogix 75
- 1500 System 75
- Appendix 79
- Add the Module to Your 79
- Profile 80
- 5. Click OK 80
- Configure Each I/O Module 82
- Positive Decimal Values 83
- Negative Decimal Values 84
- Glossary 85
- Ideal Transfer 87
- Actual Transfer 87
- Function 87
- Rockwell Automation 94
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 1769-IF4FXOF2F Compact Combination Fast Analog I/O
Ekwipunek Rockwell-automation 1791R-XXXX CompactBlock Distributed I/O on Remote Instrukcja Użytkownika
(36 strony)
(36 strony)
Ekwipunek Rockwell-automation 1747-SCNR ControlNet Scanner Module Reference Manu Instrukcja Użytkownika
(144 strony)
(144 strony)
Ekwipunek Rockwell-automation 1734-SSI POINT I/O Synchronous Serial Interface Ab Instrukcja Użytkownika
(53 strony)
(53 strony)
Ekwipunek Rockwell-automation 1769-OF2 Compact I/O Analog Modules Instrukcja Użytkownika
(184 strony)
(184 strony)
Ekwipunek Rockwell-automation 1785-BCM_BEM, D17856.5.4 PLC-5 Backup Communicatio Instrukcja Użytkownika
(161 strony)
(161 strony)
Ekwipunek Rockwell-automation 1785-RC Application Relay Interface Installation I Instrukcja Użytkownika
(12 strony)
(12 strony)
Ekwipunek Rockwell-automation 1791DS-IB16 CompactBlock Guard I/O DeviceNet Safet Instrukcja Użytkownika
(24 strony)
(24 strony)
Ekwipunek Rockwell-automation 1734-IV4/C Point I/O Source Input Module Installat Instrukcja Użytkownika
(24 strony)
(24 strony)
Ekwipunek Rockwell-automation 1771-IBN DC (10-30V) INPUT Module Installation Ins Instrukcja Użytkownika
(20 strony)
(20 strony)
Ekwipunek Rockwell-automation 1786-RPA/B ControlNet Modular Repeater Adapter Ins Instrukcja Użytkownika
(24 strony)
(24 strony)
Ekwipunek Rockwell-automation 1793-IB2XOB2PS FLEX INTEGRA 2 INPUT/2 PROTECTED OU Instrukcja Użytkownika
(12 strony)
(12 strony)
Ekwipunek Rockwell-automation 1762-IQ8OW6 DC-Input/Relay-Output Combination Modu Instrukcja Użytkownika
(20 strony)
(20 strony)
Ekwipunek Rockwell-automation 1771-OVN DC Output Mod. Installation Instructions Instrukcja Użytkownika
(16 strony)
(16 strony)
Ekwipunek Rockwell-automation 1748 DataSite Configured Panel Installation Instru Instrukcja Użytkownika
(56 strony)
(56 strony)
Ekwipunek Rockwell-automation 1734-OB2E_4E_8E, Series C POINT I/O Protected Outp Instrukcja Użytkownika
(22 strony)
(22 strony)
Ekwipunek Rockwell-automation 1790P-T4T0 CompactBlock LDX I/O Thermocouple Modul Instrukcja Użytkownika
(112 strony)
(112 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji