Rockwell-automation 20-COMM-ER 20-COMM-ER Dual-Port EtherNet/IP Commun Instrukcja Użytkownika Strona 174
- Strona / 238
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
174 Rockwell Automation Publication 20COMM-UM015B-EN-P - July 2013
Appendix B Adapter Parameters
23 [Comm Flt Action]
Sets the action that the adapter and drive will take
if the adapter detects that I/O communication has
been disrupted. This setting is effective only if I/O
that controls the drive is transmitted through the
adapter. When communication is re-established,
the drive will automatically receive commands over
the network again.
Default: 0 = Fault
Values: 0 = Fault
1 = Stop
2 = Zero Data
3 = Hold Last
4 = Send Flt Cfg
Type: Read/Write
Reset Required: No
24 [Idle Flt Action]
Sets the action that the adapter and drive will take
if the adapter detects that the controller is in
program mode or faulted. This setting is effective
only if I/O that controls the drive is transmitted
through the adapter. When the controller is put
back in Run mode, the drive will automatically
receive commands over the network again.
Default: 0 = Fault
Values: 0 = Fault
1 = Stop
2 = Zero Data
3 = Hold Last
4 = Send Flt Cfg
Type: Read/Write
Reset Required: No
25 [DPI I/O Cfg]
Sets the I/O that is transferred through the adapter.
Default: xxx0 0001
Bit Values: 0 = I/O Disabled
1 = I/O Enabled
Type: Read/Write
Reset Required: Yes
Parameter
No. Name and Description Details
ATTENTION: Risk of injury or equipment damage exists. Parameter 23 -
[Comm Flt Action] lets you determine the action of the adapter and connected
drive if I/O communication is disrupted. By default, this parameter faults the
drive. You can set this parameter so that the drive continues to run, however,
precautions should be taken to verify that the setting of this parameter does not
create a risk of injury or equipment damage. When commissioning the drive,
verify that your system responds correctly to various situations (for example, a
disconnected cable).
ATTENTION: Risk of injury or equipment damage exists. Parameter 24 - [Idle
Flt Action] lets you determine the action of the adapter and connected drive
when the controller is idle. By default, this parameter faults the drive. You can
set this parameter so that the drive continues to run, however, precautions
should be taken to verify that the setting of this parameter does not create a risk
of injury or equipment damage. When commissioning the drive, verify that your
system responds correctly to various situations (for example, a faulted
controller).
Bit
Definition
Not Used
Not Used
Not Used
Datalink D
Datalink C
Datalink B
Datalink A
Cmd/Ref
Default xxx00001
Bit 76543210
- User Manual 1
- Important User Information 2
- Table of Contents 3
- Chapter 4 4
- Configuring the I/O 4
- Chapter 5 4
- Using the I/O 4
- Chapter 6 4
- About This Manual 7
- Conventions Used in This 7
- Rockwell Automation 7
- Additional Resources 8
- Getting Started 11
- Features 12
- Compatible Products 13
- Required Equipment 13
- Safety Precautions 15
- Quick Start 16
- Installing the Adapter 17
- Preparing for an 18
- Installation 18
- Setting the Web Pages 19
- Connecting the Adapter to 20
- Applying Power 24
- and page 145 25
- Commissioning the Adapter 26
- Configuring the Adapter 27
- Using the PowerFlex 7 28
- Class HIM 28
- Using BOOTP 29
- Setting the IP Address 32
- Subnet Mask, and Gateway 32
- Setting the Data Rate 34
- Setting the I/O 35
- Configuration 35
- Selecting Master-Slave or 36
- Peer-to-Peer 36
- Communication) 37
- Setting the Reference 41
- Adjustment 41
- Setting a Fault Action 41
- Setting Web Access 42
- Resetting the Adapter 43
- Viewing the Adapter Status 44
- Using Parameters 44
- Updating the Adapter 44
- Firmware 44
- Figure 9 - Controller Tags 57
- Figure 11 - Controller Tags 66
- Limitations Using a 68
- Controller 68
- Controller Example 68
- Select the Controller 70
- Steps 2…5 71
- Steps 6…9 71
- Timeout 72
- Datalink Out 73
- Steps 1…4 73
- Steps 5…8 73
- Understanding the I/O 80
- · PowerFlex 700H drives 81
- Using Logic Command/ 84
- Using Reference/Feedback 84
- Par. 82 - [Maximum Speed] 85
- Using Datalinks 86
- Example Ladder Logic 87
- Program Information 87
- Logic Program 91
- Example Datalink Data 94
- Generic Profile 95
- 50 Controllers 99
- Using Explicit Messaging 105
- About Explicit Messaging 106
- Performing Explicit 106
- Messages 106
- ControlLogix Controller 108
- Examples 108
- Parameter 121
- 7-Class drive 123
- MicroLogix 1100/1400 124
- Controller Examples 124
- Read/Write Parameter Service 125
- Single Parameter 130
- Troubleshooting 143
- Port Status Indicator 144
- Network Status Indicator 145
- Link (LS1, LS2) Status 145
- Indicator 145
- NET A Status Indicator 145
- Hardware Reset via Node 146
- Switches 146
- Viewing Adapter 146
- Diagnostic Items 146
- Viewing and Clearing 149
- Table 25 - Adapter Events 150
- Viewing the Adapter Web Pages 153
- Process Display Home 156
- Browse DPI Device Folder 156
- Diagnostics Web Page 157
- Network Setting Link 158
- EtherNet/IP Statistics Link 159
- Ring Statistics link 159
- Administrative Web Pages 160
- Device Identity Link 161
- Network Configuration Link 161
- Email Configuration Link 162
- Password Configuration 165
- Kit (20-XCOMM-DC-BASE) 167
- Specifications 169
- Mechanical 170
- Environmental 170
- Regulatory Compliance 170
- Adapter Parameters 171
- EtherNet/IP Objects 181
- Identity Object 182
- Assembly Object 183
- Register Object 184
- Parameter Object 185
- Instances 186
- Class Attributes 186
- Instance Attributes 187
- Parameter Group Object 188
- Device Level Ring Object 189
- Quality of Service Object 190
- PCCC Object 190
- DPI Device Object 196
- DPI Parameter Object 198
- Formula number 201
- Extended DPI descriptor 201
- DPI Fault Object 204
- DPI Alarm Object 206
- DPI Diagnostic Object 207
- DPI Time Object 209
- TCP/IP Interface Object 211
- Ethernet Link Object 213
- Logic Command/Status Words 215
- Logic Status Word 216
- PowerFlex 700S Drives 217
- SMC Flex Controllers 219
- SMC-50 Controllers 219
- Logic Command Word (Control) 220
- Glossary 221
- D Data Rate 222
- Glossary 223
- F Fault Action 224
- G Gateway 225
- H Hardware Address 225
- I Idle Action 225
- L Logic Command/Logic Status 226
- M Master-Slave Hierarchy 227
- N NVS (Nonvolatile Storage) 227
- R Reference/Feedback 227
- S Scanner 228
- Z Zero Data 229
- Index 233
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 20-COMM-ER 20-COMM-ER Dual-Port EtherNet/IP Commun
Ekwipunek Rockwell-automation 20D PowerFlex 700S Drive Ph I Control, Frames 1... Instrukcja Użytkownika
(248 strony)
(248 strony)
(2 strony)
Ekwipunek Rockwell-automation 23P PowerFlex DC Stand-Alone Regulator (SAR) Capac Instrukcja Użytkownika
(10 strony)
(10 strony)
Ekwipunek Rockwell-automation 56RF High Frequency 13.56 MHz RFID EtherNet/IP Int Instrukcja Użytkownika
(20 strony)
(20 strony)
Ekwipunek Rockwell-automation 20P PowerFlex DC Drive - Frame B Switching Power S Instrukcja Użytkownika
(10 strony)
(10 strony)
Ekwipunek Rockwell-automation 23C PowerFlex 400 AC Drive Packages for Fan & Instrukcja Użytkownika
(202 strony)
(202 strony)
Ekwipunek Rockwell-automation 20P PowerFlex DC Drive - Frame A SCR Modules for D Instrukcja Użytkownika
(18 strony)
(18 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji