Rockwell-automation 20-COMM-R Remote I/O Adapter Instrukcja Użytkownika Strona 24
- Strona / 128
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
2-8 Installing the Adapter
20-COMM-R Remote I/O Adapter User Manual
Publication 20COMM-UM004D-EN-P
6. If the adapter is at the end of the Remote I/O link, connect a termination
resistor (see Figure 2.7
).
The resistor should have a value of 82 or 150 ohms (82 ohms is
preferred).
Important: If the Remote I/O network is operating at 230.4 Kbps, an
82 ohm termination resistor must be used.
Important: If any of the following products, which cannot operate at
230.4 Kbps, are on the Remote I/O network, a 150 ohm
termination resistor must be used.
Figure 2.7 Connecting a Termination Resistor (if required)
7. Connect the Remote I/O cable plug to the adapter’s mating connector.
Applying Power
Install the drive cover or close the drive door, and apply power to the drive.
The adapter receives its power from the connected drive. When you apply
power to the adapter for the first time, its topmost ‘PORT’ status indicator
should be steady green or flashing green after an initialization. If it is red,
there is a problem. See Chapter 6
, Troubleshooting.
Start-Up Status Indications
Status indicators for the drive and communication adapter can be viewed on
the front of the drive (Figure 2.8
) after power has been applied. Possible
start-up status indications are shown in Table 2.A
.
• 1771-SN scanner • 6008-SQH1 scanner
• 1772-SD scanner • 6008-SQH scanner
• 1772-SD2 scanner • 1771-AS adapter
• 1772-SR scanner • 1772-ASB (Ser. A) adapter
• 1775-S4A scanner • 1771-DCM adapter
• 1775-S4B scanner • 1771-AF device
Clear
Termination Resistor
(82 Ohms or 150 Ohms)
Shield
Blue
!
ATTENTION: Risk of equipment damage, injury, or death
exists. Unpredictable operation may occur if you fail to verify
that parameter settings are compatible with your application.
Verify that settings are compatible with your application before
applying power to the drive.
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- About This Manual 7
- Rockwell Automation 8
- Additional Resources 8
- Resource Description 9
- About This Manual P-3 9
- P-4 About This Manual 10
- Getting Started 11
- Features 12
- Compatible Products 13
- Required Equipment 13
- User-Supplied Equipment 14
- Safety Precautions 15
- Quick Start 16
- Installing the Adapter 17
- Commissioning the Adapter 18
- Connecting the Adapter to 20
- Applying Power 24
- 2-10 Installing the Adapter 26
- Configuring the Adapter 27
- Using the PowerFlex 7-Class 28
- HIM to Access Parameters 28
- Setting the Rack Address 29
- Setting the Baud Rate 30
- Setting the Starting Module 30
- Setting the Last Rack 31
- Setting the Rack Size 31
- Setting the I/O 32
- Configuration 32
- Setting a Fault Action 33
- Resetting the Adapter 34
- Viewing the Adapter Status 35
- Using Parameters 35
- Updating the Adapter 36
- Firmware 36
- Chapter 4 37
- Understanding the I/O Image 38
- Discrete I/O Image 40
- Size Valid Values 41
- 16-bit -32768 to 32767 41
- Block Transfer I/O Image 43
- Rules for Using Datalinks 44
- Datalink Scaling 45
- Example Ladder Logic 47
- Program Information 47
- ControlLogix Controller 48
- PLC-5 Controller Example 51
- Block Transfer Read 53
- Block Transfer Write 54
- All Controller Versions 55
- Chapter 5 59
- About Block Transfer 60
- Messaging 60
- Formatting Block Transfer 60
- Messages 60
- Executing Block Transfers 63
- Example Programs 64
- Ladder Logic Program 66
- SLC 500 Controller 69
- Examples 69
- Troubleshooting 75
- PORT Status Indicator 76
- MOD Status Indicator 76
- NET A Status Indicator 77
- Viewing Adapter Diagnostic 77
- Viewing and Clearing 79
- Table 6.B Adapter Events 80
- Specifications 81
- Regulatory Compliance 82
- Adapter Parameters 83
- CIP Objects 87
- Common Messages 88
- DPI Device Object 89
- DPI Parameter Object 91
- Descriptor Attributes 93
- Formulas for Converting 94
- Object-Specific Services 94
- DPI error code 95
- DPI Fault Object 101
- Instance Attributes 102
- DPI Alarm Object 103
- DPI Time Object 105
- C-20 CIP Objects 106
- Logic Command/Status Words 107
- Logic Status Word 108
- PowerFlex 700S (Phase II 109
- Control) and 700L (with 109
- 700S Control) Drives 109
- PowerFlex 750-Series Drives 111
- PowerFlex Digital DC Drives 113
- Glossary 115
- D Datalinks 116
- F Fault Action 117
- I Idle Action 118
- L Last RIO Rack 118
- N NVS (Nonvolatile Storage) 118
- R Rack Address 119
- S Scanner 120
- U Update 120
- Z Zero Data 120
- Rockwell Automation Support 128
- Documentation Feedback 128
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 20-COMM-R Remote I/O Adapter
Ekwipunek Rockwell-automation 20P PowerFlex DC Drive - Frame B Bimetal Thermosta Instrukcja Użytkownika
(16 strony)
(16 strony)
Ekwipunek Rockwell-automation 23P PowerFlex DC Stand-Alone Regulator (SAR) Field Instrukcja Użytkownika
(10 strony)
(10 strony)
(6 strony)
Ekwipunek Rockwell-automation 20B PowerFlex 700 Gasket Kit - Frames 7-10 Instrukcja Użytkownika
(6 strony)
(6 strony)
Ekwipunek Rockwell-automation 45FSL General Purpose Fiber Optic Sensors Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Rockwell-automation 1203-SSS Smart Self-powered Serial Converter Instrukcja Użytkownika
(60 strony)
(60 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.167 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji