Rockwell-automation 20G PowerFlex 755 Drive Embedded EtherNet/IP Adapt Instrukcja Użytkownika Strona 20
- Strona / 190
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
20 Rockwell Automation Publication 750COM-UM001E-EN-P - October 2013
Chapter 2 Installing the Adapter
The switch settings can be verified by viewing Diagnostic Device Item number 68
(page 111
) with any of the following drive configuration tools:
• PowerFlex 20-HIM-A6 or 20-HIM-C6S HIM
• Connected Components Workbench software, version 1.02 or later
• DriveExplorer software, version 6.01 or later
• DriveExecutive software, version 5.01 or later
Also, you can use Parameter 37 - [Net Addr Src], a read-only parameter, to
verify the selected setting for Parameter 36 - [BOOTP].
Connecting the Adapter to
the Network
1. Remove power from the drive.
2. Remove the drive cover and lift up the drive HIM bezel to its open
position to access the drive control pod.
3. Use static control precautions.
4. Connect one end of an Ethernet cable to the network.
See Figure 2
for an example of wiring to an EtherNet/IP network.
Figure 2 - Connecting the Ethernet Cable to the Network
5. Route the other end of the Ethernet cable through the bottom of the
PowerFlex 755 drive, and insert the cable plug into the embedded
EtherNet/IP adapter mating socket (item 3 in Components
on page 11).
ATTENTION: Risk of injury or death exists. The PowerFlex drive may contain high
voltages that can cause injury or death. Remove power from the drive, and then
verify power has been discharged before connecting the embedded EtherNet/IP
adapter to the network.
Ethernet
Switch
Controller
(ControlLogix shown with
1756-ENBT Bridge)
PowerFlex 755 Drives
(each with embedded EtherNet/IP adapter)
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- New and Updated 3
- Information 3
- Table of Contents 5
- Conventions Used in This 9
- Rockwell Automation 9
- Additional Resources 10
- Getting Started 11
- Features 12
- Compatible Products 13
- Required Equipment 13
- Chapter 1 Getting Started 14
- Safety Precautions 15
- Quick Start 16
- Installing the Adapter 17
- Setting the IP Address 18
- Connecting the Adapter to 20
- Applying Power 21
- Commissioning the Adapter 24
- Configuring the Adapter 25
- Using the PowerFlex 20-HIM 26
- A6 or 20-HIM-C6S HIM to 26
- Access Parameters 26
- Setting the Adapter IP 26
- Enabled 1 27
- Disable the BOOTP Feature 30
- Set the IP Address 30
- Set the Subnet Mask 30
- Setting the Data Rate 31
- Selecting Master-Slave or 32
- Peer-to-Peer Hierarchy 32
- Enable Datalinks To Read Data 33
- 0<<2 35
- Custom Peer I/O Configuration 36
- 10.00 Secs 37
- Setting a Fault Action 38
- Setting Web Access Control 40
- Resetting the Adapter 41
- Restoring Adapter 41
- Parameters to Factory 41
- Defaults 41
- ESC soft 42
- Viewing the Adapter Status 42
- Using Parameters 42
- Updating the Adapter 43
- Firmware 43
- Configuring the I/O 45
- ControlLogix Example 46
- Chapter 4 Configuring the I/O 50
- Configuring the I/O Chapter 4 53
- ADC and Logix Memory 66
- Monitoring ADC Progress 71
- Using the I/O 79
- Understanding the 80
- ControlLogix Controller I/O 80
- Using Logic Command/Status 81
- Using Reference/Feedback 81
- Using Datalinks 82
- Example Ladder Logic 83
- Program Information 83
- ControlLogix Controller 84
- Using the I/O Chapter 5 85
- Versions 86
- Program 87
- Program Tags 88
- Example Datalink Data 89
- Generic Profile 90
- Using Explicit Messaging 91
- About Explicit Messaging 92
- Examples 94
- Single Parameter 96
- Multiple Parameters 101
- Request (Source Data) array 105
- Troubleshooting 107
- ENET Status Indicator 108
- LINK Status Indicator 108
- Viewing Adapter Diagnostic 109
- Viewing and Clearing Events 111
- Table 12 - Adapter Events 112
- Viewing the Adapter Web Pages 113
- Process Display Pop-up 116
- Dialog Box 116
- TCP/IP Configuration Web 117
- Web Page 118
- Device Information Pages 121
- EtherNet/IP adapter) 123
- Specifications 125
- Appendix A Specifications 126
- Adapter Parameters 127
- Parameter List 128
- EtherNet/IP Objects 137
- Identity Object 138
- Assembly Object 139
- Register Object 140
- PCCC Object 141
- N-Files 143
- DPI Device Object 145
- Class Attributes 146
- Instance Attributes 147
- DPI Parameter Object 148
- Formula number 150
- Extended DPI descriptor 150
- Descriptor Attributes 151
- Formulas for Converting 153
- Common Services 153
- Object Specific Services 153
- DPI Fault Object 154
- DPI Alarm Object 156
- DPI Diagnostic Object 158
- DPI Time Object 160
- Host DPI Parameter Object 162
- TCP/IP Interface Object 168
- Ethernet Link Object 170
- 750-Series Drives 173
- History of Changes 175
- Glossary 177
- Rockwell Automation Support 190
- Documentation Feedback 190
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 20G PowerFlex 755 Drive Embedded EtherNet/IP Adapt
(2 strony)
(4 strony)
Ekwipunek Rockwell-automation 509-TA_ Size 00 Enclosure Cover Replacement Instrukcja Użytkownika
(1 strony)
(1 strony)
Ekwipunek Rockwell-automation 825P Modular Protection System Quick Start Guide Instrukcja Użytkownika
(32 strony)
(32 strony)
Ekwipunek Rockwell-automation 842E EtherNet/IP Multi-Turn Encoders Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Rockwell-automation 440P Small Metal Safety Position Switches Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Rockwell-automation 281G ArmorStart - Safety Version - Getting Started Instrukcja Użytkownika
(24 strony)
(24 strony)
Ekwipunek Rockwell-automation 800Z Touch Button and Guard Installation Instrukcja Użytkownika
(1 strony)
(1 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji