Rockwell-automation AutoMax ControlNet Communication Interface Module Instrukcja Użytkownika Strona 16
- Strona / 80
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Page 16 AutoMax ControlNet Module
Publication number DSMBCN-UM001B-EN-P February 2003
The LEDs do not reflect the state of the NAP port. If you connect the
MBCN to the network via the NAP port, the two network status LEDs
flash red together.
Priority State How to view Cause
1
(highest)
Both steady
off
Reset or no power
2 Both steady
red
Failed link interface
Fatal error on MBCN
3 Alternating
red/green
Self test
4 Alternating
red/off
Viewed
together
Bad node configuration, such
as duplicate address
5 Steady off Channel disabled or channel
not supported
6 Flashing
red/green
Invalid link configuration,
such as address > UMAX
7 Flashing
red/off
Link fault or no MAC frames
received
8 Flashing
green/off
Temporary channel error, or
listen only
9
(lowest)
Steady green
Viewed
Independently
Normal operation
Figure 2 LED Status Table
7-Segment LED Codes
Value Meaning
1 NAM not attached. There are no other nodes
on the network.
2 Keeper faulted master. The MBCN schedule
needs to be updated using RSNetWorx.
3 Keeper faulted backup. The MBCN schedule
needs to be updated using RSNetWorx.
4 Keeper change
5 Keeper faulted change
6 Keeper temporary state
b Inactive. The MBCN is online but has no
scheduled connections and is not sending or
receiving messages.
- User Manual 1
- Important User Information 2
- Table of Figures 7
- Introduction 9
- Getting Support 10
- Reference Documents 10
- Requirements 10
- Overview 11
- Module Overview 11
- Hardware Features 13
- MAC ID Thumbwheels 14
- Serial Configuration Port 14
- NAP Port 15
- ControlNet Connectors 15
- Network Status LEDs 15
- 7-Segment LED Codes 16
- Figure 3 7-Segment LED Codes 17
- Contact technical support 17
- Communication Error 18
- Installation 19
- Installation and Wiring 20
- Connecting to the Network 21
- Quick Start 22
- Programming the MBCN 23
- Creating a Configuration 24
- Configuring 1771 I/O 25
- Configuring Flex I/O 26
- Analog Connection 27
- Putting the MBCN in Run Mode 32
- Accessing I/O Data 32
- Application Example 33
- Multicast Connections 34
- Monitoring Module Operation 35
- Operating Status 38
- AutoMax 40
- Registers 40
- Name Description 40
- Unscheduled Messaging 41
- WARNING 43
- GATEWAY_CMD_OK@ Status Codes 51
- Commands from Remote Nodes 54
- Viewing Network Parameters 57
- Pending Network Parameters 58
- Name Register Description 59
- State Registers 60
- Keeper State 61
- Flash State 62
- Serial CONFIG Port State 62
- Channel State 63
- Diagnostic Counters 64
- Module Specific Counters 65
- The Error Log 66
- Active Node List 67
- ID Area 68
- Serial Number 69
- Product Name Length 69
- Product Name 69
- Current Address 70
- MAC ID Switches 70
- Summary of ID Area Locations 70
- Firmware Version Information 71
- Using the Host Watchdog 72
- Updating the Firmware 73
- PGA Config Write Successful 75
- **** Cycle Power **** 75
- Specifications 78
- Support 79
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation AutoMax ControlNet Communication Interface Module
Ekwipunek Rockwell-automation T8312 Trusted Expander Interface Adaptor Unit Instrukcja Użytkownika
(2 strony)
(2 strony)
Ekwipunek Rockwell-automation 1440-TB-H XM-947 Dynamic Vibration Terminal Base Instrukcja Użytkownika
(24 strony)
(24 strony)
Ekwipunek Rockwell-automation 1766-L32 Pump Station Controller Quick Start Instrukcja Użytkownika
(52 strony)
(52 strony)
Ekwipunek Rockwell-automation 1786-series ControlNet Fiber Media Planning and In Instrukcja Użytkownika
(88 strony)
(88 strony)
Ekwipunek Rockwell-automation T8270 Trusted Fan-Tray 24V dc Rack Mounted Instrukcja Użytkownika
(2 strony)
(2 strony)
(4 strony)
Ekwipunek Rockwell-automation T8802 Trusted 24 Vdc Digirtal Input FTA - 60 Chann Instrukcja Użytkownika
(16 strony)
(16 strony)
Ekwipunek Rockwell-automation FactoryTalk Historian SE 3.0 UniInt Interface User Instrukcja Użytkownika
(108 strony)
(108 strony)
Ekwipunek Rockwell-automation T8471 Trusted TMR 120V dc Digital Output Module Instrukcja Użytkownika
(2 strony)
(2 strony)
Ekwipunek Rockwell-automation 1440-TB-A XM-940 Dynamic Measurement Terminal Base Instrukcja Użytkownika
(22 strony)
(22 strony)
Ekwipunek Rockwell-automation Logix5000 Control Systems: Connect a PowerFlex 70 Instrukcja Użytkownika
(54 strony)
(54 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji