Rockwell-automation AutoMax ControlNet Communication Interface Module Instrukcja Użytkownika Strona 29
- Strona / 80
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
AutoMax ControlNet Module Page 29
Publication number DSMBCN-UM001B-EN-P February 2003
3. Set the Connection Name to Consume Data From.
4. RSNetWorx assigns the Producer ID automatically. If necessary,
change the value.
5. Set the Requested Packet Interval to the desired update rate. The RPI
must be greater than or equal to the network update time (NUT).
6. Set the Input Size to the number of words of data you wish the
MBCN to produce.
7. RSNetWorx assigns the Input Address, Output Address and Status
Address automatically if Enable automatic addressing on insert is
turned on. If you want to manually assign these addresses, enter the
values.
8. Click OK to accept the settings.
RSNetWorx automatically creates a matching produce target in the
MBCN. Start the Scanlist Configuration tool for the MBCN and confirm
that this is so.
Configuring Scheduled Data with a ControlLogix Processor
To exchange scheduled data with a ControlLogix processor, you must
first create user-defined data types for the data in the ControlLogix, then
create tags of the types you have created. This must be done offline in
RSLogix 5000.
Produced Data on the ControlLogix, Consumed on the MBCN
Use the following steps to create a produced tag in RSLogix 5000:
1. Expand the Data Types item in the tree, right click on User-Defined,
and select New Data Type...
In the dialog box that appears:
2. Give the new type a name, for example, ProdTagType, and
optionally a Description.
3. Create a member for the data type. This member should be an array
of INTs of the size of data that you want to transfer. The maximum
size is 240 words, but this may be further restricted by the network
schedule.
4. Click OK to accept the data type.
5. Expand the Controller in the tree. Right click on Controller Tags
and select Edit Tags. RSLogix 5000 displays a list of the existing
controller tags
6. Right click on an empty entry in the list and select Edit Tag
Properties.
In the dialog box that appears:
7. Give the tag a Name and optionally a description.
- User Manual 1
- Important User Information 2
- Table of Figures 7
- Introduction 9
- Getting Support 10
- Reference Documents 10
- Requirements 10
- Overview 11
- Module Overview 11
- Hardware Features 13
- MAC ID Thumbwheels 14
- Serial Configuration Port 14
- NAP Port 15
- ControlNet Connectors 15
- Network Status LEDs 15
- 7-Segment LED Codes 16
- Figure 3 7-Segment LED Codes 17
- Contact technical support 17
- Communication Error 18
- Installation 19
- Installation and Wiring 20
- Connecting to the Network 21
- Quick Start 22
- Programming the MBCN 23
- Creating a Configuration 24
- Configuring 1771 I/O 25
- Configuring Flex I/O 26
- Analog Connection 27
- Putting the MBCN in Run Mode 32
- Accessing I/O Data 32
- Application Example 33
- Multicast Connections 34
- Monitoring Module Operation 35
- Operating Status 38
- AutoMax 40
- Registers 40
- Name Description 40
- Unscheduled Messaging 41
- WARNING 43
- GATEWAY_CMD_OK@ Status Codes 51
- Commands from Remote Nodes 54
- Viewing Network Parameters 57
- Pending Network Parameters 58
- Name Register Description 59
- State Registers 60
- Keeper State 61
- Flash State 62
- Serial CONFIG Port State 62
- Channel State 63
- Diagnostic Counters 64
- Module Specific Counters 65
- The Error Log 66
- Active Node List 67
- ID Area 68
- Serial Number 69
- Product Name Length 69
- Product Name 69
- Current Address 70
- MAC ID Switches 70
- Summary of ID Area Locations 70
- Firmware Version Information 71
- Using the Host Watchdog 72
- Updating the Firmware 73
- PGA Config Write Successful 75
- **** Cycle Power **** 75
- Specifications 78
- Support 79
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation AutoMax ControlNet Communication Interface Module
Ekwipunek Rockwell-automation T8312 Trusted Expander Interface Adaptor Unit Instrukcja Użytkownika
(2 strony)
(2 strony)
Ekwipunek Rockwell-automation 1440-TB-H XM-947 Dynamic Vibration Terminal Base Instrukcja Użytkownika
(24 strony)
(24 strony)
Ekwipunek Rockwell-automation 1766-L32 Pump Station Controller Quick Start Instrukcja Użytkownika
(52 strony)
(52 strony)
Ekwipunek Rockwell-automation 1786-series ControlNet Fiber Media Planning and In Instrukcja Użytkownika
(88 strony)
(88 strony)
Ekwipunek Rockwell-automation T8270 Trusted Fan-Tray 24V dc Rack Mounted Instrukcja Użytkownika
(2 strony)
(2 strony)
(4 strony)
Ekwipunek Rockwell-automation T8802 Trusted 24 Vdc Digirtal Input FTA - 60 Chann Instrukcja Użytkownika
(16 strony)
(16 strony)
Ekwipunek Rockwell-automation FactoryTalk Historian SE 3.0 UniInt Interface User Instrukcja Użytkownika
(108 strony)
(108 strony)
Ekwipunek Rockwell-automation T8471 Trusted TMR 120V dc Digital Output Module Instrukcja Użytkownika
(2 strony)
(2 strony)
Ekwipunek Rockwell-automation 1440-TB-A XM-940 Dynamic Measurement Terminal Base Instrukcja Użytkownika
(22 strony)
(22 strony)
Ekwipunek Rockwell-automation Logix5000 Control Systems: Connect a PowerFlex 70 Instrukcja Użytkownika
(54 strony)
(54 strony)
Sony PCG-808 manuales
Manuales del propietario y guías del usuario para Cuadernos Sony PCG-808.
Ofrecemos 1 manuales en pdf Sony PCG-808 para descargar gratis por tipos de documentos: Manual de usuario
Komentarze do niniejszej Instrukcji