Rockwell-automation 1771-N SERIES High Resolution Analog Module User M Instrukcja Użytkownika Strona 158
- Strona / 188
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Block Transfer Write and Block Transfer Read Configurations for 6 Output/2 Input 1771-N Series ModulesI–6
Publication 1771ĆUM127B-EN-P - December 2002
Definition
Decimal Bit
(Octal Bit)
Word
Bits 00-07
10 ohm offset. Compensates for a resistance offset on a 10
ohm copper RTD. Range of +
0.99 ohms, in units of 0.01 ohms.
This field must be 0 for all other RTDs.
Bits 08-10
(10-12)
RTD type. Specifies type of RTD linearization on RTD
channels:
001 = 100 ohm Pt, European standard;
010 = 100 ohm Pt. US standard;
011 = 10 ohm copper;
100 = 120 ohm nickel.
This field is 0 for non-RTD channels.
Word 51
Bit 11 (13)
Constant = 0
Bits 12-15
(14-17)
Thermocouple type. Specifies type of TC linearization on TC
channels.
0000 = millivolts;
0001 = B;
0010 = E;
0011 = J;
0100 = K;
0101 = R;
0110 = S;
0111=T.
This field must be 0 for non-thermocouple channels.
Words 52 thru 58 Same as words 45 thru 51 but for channel 8.
Block Transfer Read Word Assignments for 6 Output/2 Input
Modules
Word/Dec. Bit
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
Word/Octal Bit
17 16 15 14 13 12 11 10 07 06 05 04 03 02 01 00
0 Constant = 8800 Hexadecimal
1
Power
up
Bad
Chan.
Data
Mod
Alarm
RTS
Time
out
I/O
Reset
Program
Verify
Mod
Fault
Bad
Prog
Bad
Struct
Unused = 0
2 1 Unused = 0
CJC
Over
Range
CJC
Under
Range
3 Cold Junction Temperature; Units of 0.01 degrees C or 0.1 degrees F
Channel 1 Status
4 0 Unused = 0
Bad
Calib
Bad
Prog
Bad
Data
Rate
Alarm
High
Clamp
Low
Clamp
Unused = 0
5 Channel 1 Raw Count sent to DAC
Channel 2 Status
6 0 Unused = 0
Bad
Calib
Bad
Prog
Bad
Data
Rate
Alarm
High
Clamp
Low
Clamp
Unused = 0
7 Channel 2 Raw Count sent to DAC
- User Manual 1
- Important User Information 2
- ATTENTION 3
- Using this Manual 5
- Related Products 6
- Product Compatibility 6
- Related Publications 7
- Using this ManualP–4 8
- Table of Contents 9
- Chapter 4 10
- Configuring the Module 10
- Table of Contents toc-iii 11
- Table of Contentstoc-iv 12
- Table of Contents toc-v 13
- Table of Contentstoc-vi 14
- Overview of the High 15
- Resolution Isolated 15
- Analog Modules 15
- Features of the High 16
- Analog Series Modules 16
- Refer to 17
- Appendix 17
- Installing the Module 19
- Determine Module 20
- Location in the I/O Chassis 20
- Install the Analog Module 20
- Install the Module in the 21
- Chassis and Connect the 21
- Connecting Wiring 23
- • R = return 26
- • I = input 26
- • O = output 26
- • S = shield 26
- Connecting 4ĆWire 27
- Sourcing Input Analog 28
- Making Your Own Cables 29
- Grounding the Field 30
- Interpreting the 31
- Indicator Lights 31
- Chapter Summary 31
- 2–14 Installing the Module 32
- Communicating With Your 33
- Analog Module 33
- PLCĆ2 Programming 34
- PLCĆ3 Program Example 34
- PLCĆ5 and PLCĆ5/250 35
- Program Example 35
- Module Scan Time 36
- Programming Samples 36
- Setting Up the Data 39
- Table File 39
- Default Configurations 42
- Module Level 43
- Programming Features 43
- Real Time Sampling 45
- Output Channel 46
- Clamping 49
- Alarm Enable 50
- Reset State 50
- Input Channel 51
- Alarm Deadband 52
- Thermocouple Type 54
- Configuration Block for a 55
- Block Transfer Write 55
- Module Status and Input Data 61
- Block Transfer Read 62
- Data Format 62
- Data Header 63
- Input Status Data 64
- Output Status Data 66
- Module Calibration 69
- Calibrating Your Module 70
- Manual Calibration 71
- Figure 6.1 73
- Termination Panel 73
- Output Channel Calibration 75
- Troubleshooting 77
- Troubleshooting with 78
- Status Reported by 78
- Specifications 81
- Grounding Guidelines." 82
- Temperature Specifications 83
- SpecificationsA–6 86
- Important: If you require 60 87
- SpecificationsA–8 88
- Word/Dec. Bit 101
- Word/Octal Bit 101
- Transfer Read Configurations 105
- Series Modules 105
- CSA Hazardous Location 183
- Rockwell Automation Support 188
- Documentation Feedback 188
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 1771-N SERIES High Resolution Analog Module User M
Ekwipunek Rockwell-automation 1792D-16VT0LP INSTL INSTR ARMORBLOCK INPUT Instrukcja Użytkownika
(8 strony)
(8 strony)
Ekwipunek Rockwell-automation 1792D-8BIO8E ArmorBlock MaXum 8 Input/8 Output Mod Instrukcja Użytkownika
(16 strony)
(16 strony)
Ekwipunek Rockwell-automation 1792D-16BT0LP INSTL INSTR ARMORBLOCK LP2 16 Instrukcja Użytkownika
(8 strony)
(8 strony)
Ekwipunek Rockwell-automation Logix5000 Controllers Major, Minor, and I/O Faults Instrukcja Użytkownika
(53 strony)
(53 strony)
Ekwipunek Rockwell-automation 1756-HIST2G FactoryTalk Historian ME 2.2 Installat Instrukcja Użytkownika
(28 strony)
(28 strony)
Ekwipunek Rockwell-automation 1769-ARM Compact Address Reserve Module Instrukcja Użytkownika
(16 strony)
(16 strony)
Ekwipunek Rockwell-automation 1793-OB4E FLEX INTEGRA 4 PROTECTED OUTPUT Instrukcja Użytkownika
(8 strony)
(8 strony)
Ekwipunek Rockwell-automation 1769-IQ6XOW4 Compact Combination 24V dc Sink/Sourc Instrukcja Użytkownika
(20 strony)
(20 strony)
Ekwipunek Rockwell-automation 1746-NO8V SLC 500 8-Point Analog Output Module/ Us Instrukcja Użytkownika
(74 strony)
(74 strony)
Ekwipunek Rockwell-automation 1771-OD16 AC (120V) ISO Output Installation Instru Instrukcja Użytkownika
(12 strony)
(12 strony)
Ekwipunek Rockwell-automation 1792D-OB4D ArmorBlock MaXum 4 Output Module Series Instrukcja Użytkownika
(16 strony)
(16 strony)
Ekwipunek Rockwell-automation 1757-ABRIO Installation Instructions Instrukcja Użytkownika
(16 strony)
(16 strony)
Ekwipunek Rockwell-automation 1747-DPS1, 1747-DPS2 Port Splitter Installation In Instrukcja Użytkownika
(24 strony)
(24 strony)
Ekwipunek Rockwell-automation 1753-IB20XOB8 GuardPLC Digital Input/Output Module Instrukcja Użytkownika
(20 strony)
(20 strony)
Ekwipunek Rockwell-automation 1793-IE4S INSTL INSTR FLEX INTEGRA 4 INPUT ANALOG Instrukcja Użytkownika
(12 strony)
(12 strony)
Ekwipunek Rockwell-automation 1785 User Mnl. PLC-5 Prog.Control Flash Instrukcja Użytkownika
(10 strony)
(10 strony)
Ekwipunek Rockwell-automation 1794-ACNR INSTL INSTR REDUNDANT MEDIA Instrukcja Użytkownika
(8 strony)
(8 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji