Rockwell-automation 25B PowerFlex 525 Embedded EtherNet/IP Adapter Instrukcja Użytkownika Strona 61
- Strona / 166
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Rockwell Automation Publication 520COM-UM001B-EN-E - March 2013 61
Chapter 5
Using the I/O
This chapter provides information and examples that explain how to control,
configure, and monitor a PowerFlex 525 drive using the configured I/O.
About I/O Messaging
On CIP-based networks, including EtherNet/IP, I/O connections are used to
transfer the data which controls the PowerFlex drive and sets its Reference. I/O
can also be used to transfer data to and from Datalinks in PowerFlex 525 drives.
The adapter includes the Logic Command, Logic Status, Reference, Feedback,
and memory allocation for the Generic Ethernet module profile (all as 16-bit
words) in the controller’s I/O image. This basic I/O must always be configured in
the Ethernet bridge using RSLogix 5000/Logix Designer. Additional I/O, if
needed, can be set using up to four Datalinks to write data and/or up to four
Datalinks to read data. When using any combination of these Datalinks, add one
16-bit word for each Datalink to the basic I/O Input Size and/or Output Size.
Chapter 3
, Configuring the Adapter, and Chapter 4, Configuring the I/O,
discuss how to configure the adapter and controller on the network for the
required I/O. The Glossary defines the different options. This chapter discusses
how to use I/O after you have configured the drive and controller.
Understanding the I/O Image
The terms input and output are defined from the controller’s point of view.
Therefore, output I/O is data that is produced by the controller and consumed by
the adapter. Input I/O is data that is produced by the adapter and consumed as
input by the controller. The I/O image will vary based on:
Topic Page
About I/O Messaging
61
Understanding the I/O Image 61
Using Logic Command/Status 62
Using Reference/Feedback 63
Using Datalinks 63
Example Ladder Logic Program Information 64
CompactLogix Example 64
ATTENTION: Risk of injury or equipment damage exists. The examples in this
publication are intended solely for purposes of example. There are many
variables and requirements with any application. Rockwell Automation, Inc.
does not assume responsibility or liability (to include intellectual property
liability) for actual use of the examples shown in this publication.
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- New and Updated 3
- Information 3
- Table of Contents 5
- Logic Command/Status Words: 7
- PowerFlex 525 Drives 7
- Overview 9
- Preface Overview 10
- Getting Started 11
- Features 12
- Compatible Products 12
- Required Equipment 12
- User-Supplied Equipment 13
- Safety Precautions 14
- Quick Start 14
- ENET LINK 15
- EtherNet/IP 15
- Chapter 1 Getting Started 16
- Setting Up the Adapter 17
- Setting the IP Address 18
- Connecting the Adapter to 18
- Startup Status Indication 19
- Commissioning the Adapter 21
- Configuring the Adapter 23
- Using the PowerFlex 4-Class 25
- HIM to Access Parameters 25
- Using BOOTP 26
- Subnet Mask, and Gateway 29
- Setting the Data Rate 30
- Using Master-Slave Hierarchy 31
- Setting a Fault Action 33
- Resetting the Adapter 34
- Viewing the Adapter Status 34
- Using Parameters 34
- Configuring the I/O 37
- CompactLogix Example 38
- 1 (Front)1 (Front)1 (Front) 38
- 2 (Rear) 38
- 00:00:BC:2E:69:F6 38
- Configuring the I/O Chapter 4 39
- Chapter 4 Configuring the I/O 40
- Controller Input Tags 45
- Controller Output Tags 45
- Differences Found Screen 48
- ADC and Logix Memory 52
- Monitoring the ADC Progress 53
- Input Image Controller Tags 58
- Output Image Controller Tags 58
- Limitations in Using 60
- MicroLogix 1100/1400 60
- Using the I/O 61
- Using Logic Command/Status 62
- Using Reference/Feedback 63
- Using Datalinks 63
- Example Ladder Logic 64
- Program Information 64
- Feedback 65
- Controller Tags 66
- Program Tags 67
- Reference 68
- Using Explicit Messaging 69
- Performing Explicit 70
- CompactLogix Examples 70
- Parameter 71
- Parameters 74
- Write Multiple Messaging 79
- 520-UM001 80
- Using Multi-Drive Mode 83
- System Wiring 85
- Understanding the I/O Image 85
- Configuring the RS-485 86
- Using Multi-Drive Add-On 87
- Multi-Drive Ladder Logic 97
- Program for Generic Profile 97
- CompactLogix Example Using 99
- Generic Profile 99
- Main Routine 100
- Drive 0...4 Control Routines 101
- Drive 0 Control Routine 102
- Drive 1 Control Routine 103
- Drive 2 Control Routine 104
- Drive 3 Control Routine 105
- Drive 4 Control Routine 106
- Multi-Drive Mode Explicit 107
- Messaging 107
- Additional Information 108
- Troubleshooting 111
- ENET Status Indicator 112
- LINK Status Indicator 112
- Viewing Adapter Diagnostic 112
- Viewing and Clearing Events 114
- Adapter Events 115
- Chapter 8 Troubleshooting 116
- Specifications 117
- Appendix A Specifications 118
- Adapter Parameters 119
- Appendix B Adapter Parameters 124
- EtherNet/IP Objects 125
- Identity Object 126
- Instance Attributes 127
- Assembly Object 128
- Register Object 129
- Instances (Multi-Drive) 130
- Class Attributes 131
- Parameter Object 132
- PCCC Object 135
- DPI Device Object 138
- Instance Attribute 140
- DPI Parameter Object 141
- on page 146 143
- Descriptor Attributes 144
- Formulas for Converting 146
- Common Services 146
- Object Specific Services 146
- DPI Fault Object 147
- TCP/IP Interface Object 149
- Ethernet Link Object 151
- Appendix D 153
- Logic Command Word 153
- Logic Status Word 154
- Position Bit Definitions 155
- Glossary 157
- Rockwell Automation Support 166
- Documentation Feedback 166
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 25B PowerFlex 525 Embedded EtherNet/IP Adapter
(6 strony)
(1 strony)
(2 strony)
Ekwipunek Rockwell-automation 440G-LZ Guard Locking Switch User Manual Instrukcja Użytkownika
(40 strony)
(40 strony)
Ekwipunek Rockwell-automation 20G PowerFlex 750-Series EMC Plate and Cores - Fra Instrukcja Użytkownika
(10 strony)
(10 strony)
Ekwipunek Rockwell-automation 440P WM3A Wide Roller with Short Lever Instrukcja Użytkownika
(2 strony)
(2 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji