Rockwell-automation 25B PowerFlex 525 Embedded EtherNet/IP Adapter Instrukcja Użytkownika Strona 85
- Strona / 166
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Rockwell Automation Publication 520COM-UM001B-EN-E - March 2013 85
Using Multi-Drive Mode Chapter 7
• Since the RS-485 ports are used for daisy-chaining the drives, there is no
connection for a peripheral device such as a HIM or USB converter
module (1203-USB). DSI Splitter cables cannot be used to add a second
connection for a peripheral device.
System Wiring
To daisy-chain the drives of the PowerFlex 525, the AK-U0-RJ45-TB2P terminal
block connector can be used for easy installation.
The wiring diagram for using AK-U0-RJ45-TB2P terminal block connectors is
shown below.
The AK-U0-RJ45-TB2P comes with (5) terminal block connectors and (2)
terminating resistors.
Understanding the I/O Image
The terms input and output are defined from the scanner’s point of view.
Therefore, Output I/O is data that is output from the scanner and consumed by
the EtherNet/IP adapter. Input I/O is status data that is produced by the adapter
and consumed as input by the scanner.
The I/O image table will vary based on the configuration of parameters C169
[MultiDrv Sel] and C175 [DSI I/O Cfg]. The image table always uses
consecutive words starting at word 0.
The Multi-Drive Example of I/O Image
on page 86 is an illustration of the
Multi-drive I/O image with 16-bit words.
To PowerFlex 525 with
embedded EtherNet/IP
To Drive #2 To Drive #3 To Drive #4 To Drive #5
120 Ω, 1/4 W
resistor
120 Ω, 1/4 W
resistor
- User Manual 1
- Important User Information 2
- Summary of Changes 3
- New and Updated 3
- Information 3
- Table of Contents 5
- Logic Command/Status Words: 7
- PowerFlex 525 Drives 7
- Overview 9
- Preface Overview 10
- Getting Started 11
- Features 12
- Compatible Products 12
- Required Equipment 12
- User-Supplied Equipment 13
- Safety Precautions 14
- Quick Start 14
- ENET LINK 15
- EtherNet/IP 15
- Chapter 1 Getting Started 16
- Setting Up the Adapter 17
- Setting the IP Address 18
- Connecting the Adapter to 18
- Startup Status Indication 19
- Commissioning the Adapter 21
- Configuring the Adapter 23
- Using the PowerFlex 4-Class 25
- HIM to Access Parameters 25
- Using BOOTP 26
- Subnet Mask, and Gateway 29
- Setting the Data Rate 30
- Using Master-Slave Hierarchy 31
- Setting a Fault Action 33
- Resetting the Adapter 34
- Viewing the Adapter Status 34
- Using Parameters 34
- Configuring the I/O 37
- CompactLogix Example 38
- 1 (Front)1 (Front)1 (Front) 38
- 2 (Rear) 38
- 00:00:BC:2E:69:F6 38
- Configuring the I/O Chapter 4 39
- Chapter 4 Configuring the I/O 40
- Controller Input Tags 45
- Controller Output Tags 45
- Differences Found Screen 48
- ADC and Logix Memory 52
- Monitoring the ADC Progress 53
- Input Image Controller Tags 58
- Output Image Controller Tags 58
- Limitations in Using 60
- MicroLogix 1100/1400 60
- Using the I/O 61
- Using Logic Command/Status 62
- Using Reference/Feedback 63
- Using Datalinks 63
- Example Ladder Logic 64
- Program Information 64
- Feedback 65
- Controller Tags 66
- Program Tags 67
- Reference 68
- Using Explicit Messaging 69
- Performing Explicit 70
- CompactLogix Examples 70
- Parameter 71
- Parameters 74
- Write Multiple Messaging 79
- 520-UM001 80
- Using Multi-Drive Mode 83
- System Wiring 85
- Understanding the I/O Image 85
- Configuring the RS-485 86
- Using Multi-Drive Add-On 87
- Multi-Drive Ladder Logic 97
- Program for Generic Profile 97
- CompactLogix Example Using 99
- Generic Profile 99
- Main Routine 100
- Drive 0...4 Control Routines 101
- Drive 0 Control Routine 102
- Drive 1 Control Routine 103
- Drive 2 Control Routine 104
- Drive 3 Control Routine 105
- Drive 4 Control Routine 106
- Multi-Drive Mode Explicit 107
- Messaging 107
- Additional Information 108
- Troubleshooting 111
- ENET Status Indicator 112
- LINK Status Indicator 112
- Viewing Adapter Diagnostic 112
- Viewing and Clearing Events 114
- Adapter Events 115
- Chapter 8 Troubleshooting 116
- Specifications 117
- Appendix A Specifications 118
- Adapter Parameters 119
- Appendix B Adapter Parameters 124
- EtherNet/IP Objects 125
- Identity Object 126
- Instance Attributes 127
- Assembly Object 128
- Register Object 129
- Instances (Multi-Drive) 130
- Class Attributes 131
- Parameter Object 132
- PCCC Object 135
- DPI Device Object 138
- Instance Attribute 140
- DPI Parameter Object 141
- on page 146 143
- Descriptor Attributes 144
- Formulas for Converting 146
- Common Services 146
- Object Specific Services 146
- DPI Fault Object 147
- TCP/IP Interface Object 149
- Ethernet Link Object 151
- Appendix D 153
- Logic Command Word 153
- Logic Status Word 154
- Position Bit Definitions 155
- Glossary 157
- Rockwell Automation Support 166
- Documentation Feedback 166
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 25B PowerFlex 525 Embedded EtherNet/IP Adapter
(6 strony)
(1 strony)
(2 strony)
Ekwipunek Rockwell-automation 440G-LZ Guard Locking Switch User Manual Instrukcja Użytkownika
(40 strony)
(40 strony)
Ekwipunek Rockwell-automation 20G PowerFlex 750-Series EMC Plate and Cores - Fra Instrukcja Użytkownika
(10 strony)
(10 strony)
Ekwipunek Rockwell-automation 440P WM3A Wide Roller with Short Lever Instrukcja Użytkownika
(2 strony)
(2 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji