Rockwell-automation 22-COMM-B PowerFlex BACnet MS/TP Adapter Instrukcja Użytkownika Strona 9
- Strona / 72
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Chapter 1
Getting Started
The adapter is intended for installation into a PowerFlex 40 or
PowerFlex 400 drive and is used for network communication. The
adapter can also be installed in a DSI External Comms Kit
(22-XCOMM-DC-BASE). This kit enables PowerFlex 4 and PowerFlex
4M drives, which cannot accommodate an internally-mounted adapter,
to connect to a BACnet MS/TP network. NOTE: The 22-COMM-B
adapter must have firmware version 1.003 (or later) to be compatible
with the PowerFlex 4M drive.
Figure 1.1 Components of the Adapter
Topic Page Topic Page
Components
1-1 Safety Precautions 1-4
Features 1-2 Quick Start 1-6
Compatible Products 1-3 Status Indicators 1-7
Required Equipment 1-3
Components
Item Component Description
➊
Status Indicators Four LEDs that indicate the status of the network connection,
DSI, and the adapter. Refer to Chapter 5
, Troubleshooting.
➋
DSI Connector A 20-pin, single-row shrouded male header. An Internal Interface
cable connects to this connector and a connector on the drive.
➌
Terminal Block A 3-pin terminal block with mating 3-pin linear plug connects the
adapter to the network.
➍
TERM, -BIAS, and
+BIAS Switches
Switches for turning on/off the adapter’s internal termination
resistor and bias resistors. See Setting the TERM, -BIAS, and
+BIAS Switches on page 2-4 for details.
➎
MAC Address
Switches
Switches for setting the MAC address. See Setting the MAC
Address on page 2-2 for details.
➌
➎
➋
➍
➊
LEDs are located
on bottom side of
adapter board
- PowerFlex® 22-COMM-B 1
- BACnet MS/TP Adapter 1
- Important User Information 2
- Summary of Changes 3
- Table of Contents 5
- About This Manual 7
- Rockwell Automation Support 8
- Getting Started 9
- Features 10
- Compatible Products 11
- Required Equipment 11
- Safety Precautions 12
- Quick Start 14
- Status Indicators 15
- 1-8 Getting Started 16
- Installing the Adapter 17
- Setting the MAC Address 18
- Installing the Adapter 2-3 19
- UP = OFF 20
- TERM Switch (SW1) 20
- RSRV Switch (SW4) 20
- Reserved for future use 20
- Installing the Adapter 2-7 23
- Applying Power 25
- Terminal Signal Function 27
- +B Signal B TxRxD+ 27
- -A Signal A TxRxD 27
- Configuring the Adapter 29
- DIAG PAR A M DSEL MEM SEL 30
- DIAG PARAM DSEL MEM SEL 30
- DIAG PA R A M DSEL MEM SEL 30
- VALUE LIMITS SEL 30
- Configuring the Adapter 3-3 31
- Building Level Network 1 32
- Building Level Network 2 32
- Device Instance Number 33
- Setting a Comm Loss Action 34
- Setting the Comm Loss Time 35
- Setting the Baud Rate 36
- Resetting the Adapter 37
- Flash Updating the Adapter 38
- Using BACnet Objects 39
- Clearing a Drive Fault 40
- Supported BACnet Objects 41
- 4-4 Using BACnet Objects 42
- Using BACnet Objects 4-5 43
- 4-6 Using BACnet Objects 44
- Troubleshooting 45
- PORT Status Indicator 46
- MOD Status Indicator 46
- NET A Status Indicator 47
- NET B Status Indicator 47
- Viewing and Clearing Events 49
- 5-6 Troubleshooting 50
- Specifications 51
- Environmental 52
- Regulatory Compliance 52
- Adapter Parameters 53
- B-2 Adapter Parameters 54
- Adapter Parameters B-3 55
- B-4 Adapter Parameters 56
- Protocol Implementation 57
- Conformance Statement (PICS) 57
- Data Link Layer Options 59
- Device Address Binding 59
- Networking Options 59
- Glossary 63
- F Fault Action 64
- I I/O Data 65
- L Logic Command/Logic Status 65
- M MAC Address 65
- N NVS (Non-Volatile Storage) 66
- R Reference/Feedback 66
- S Status Indicators 66
- Z Zero Data 66
- Numerics 67
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 22-COMM-B PowerFlex BACnet MS/TP Adapter
Ekwipunek Rockwell-automation 1336S_E Drive Multipulse Bridge Assembly Instrukcja Użytkownika
(14 strony)
(14 strony)
Ekwipunek Rockwell-automation 20P-RES-A0 PowerFlex DC Drive Resolver Feedback Op Instrukcja Użytkownika
(18 strony)
(18 strony)
Ekwipunek Rockwell-automation 20-COMM-ER 20-COMM-ER Dual-Port EtherNet/IP Commun Instrukcja Użytkownika
(238 strony)
(238 strony)
Ekwipunek Rockwell-automation 20D PowerFlex 700S Drive Ph I Control, Frames 1... Instrukcja Użytkownika
(248 strony)
(248 strony)
(2 strony)
Ekwipunek Rockwell-automation 23P PowerFlex DC Stand-Alone Regulator (SAR) Capac Instrukcja Użytkownika
(10 strony)
(10 strony)
Ekwipunek Rockwell-automation 56RF High Frequency 13.56 MHz RFID EtherNet/IP Int Instrukcja Użytkownika
(20 strony)
(20 strony)
Ekwipunek Rockwell-automation 20P PowerFlex DC Drive - Frame B Switching Power S Instrukcja Użytkownika
(10 strony)
(10 strony)
Ekwipunek Rockwell-automation 23C PowerFlex 400 AC Drive Packages for Fan & Instrukcja Użytkownika
(202 strony)
(202 strony)
Ekwipunek Rockwell-automation 20P PowerFlex DC Drive - Frame A SCR Modules for D Instrukcja Użytkownika
(18 strony)
(18 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.211 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji