Rockwell-automation RECOMM-DNET DeviceNet Adapter for use with DPI AC Instrukcja Użytkownika Strona 20
- Strona / 168
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
3-2
DeviceNet Adapter for use with DPI AC Drives
Step 2. Set the data rate switch as shown in figure 3.2
Setting Description
0-63 Node address used by the adapter if switches are
enabled. The default switch setting is 63. Node
address 63 is also the default address used by all
uncommissioned devices. Do not use this address
as the final adapter address.
Important:
If the Data Rate switch is set to “PGM”
(Program), the adapter will use the setting of DN
Addr Cfg (3) for the node address. The default
parameter setting is 63. Refer to chapter 4,
Configuring the DeviceNet Adapter.
64-99 Do not use. The adapter does not recognize these
addresses.
Figure 3.1 – Setting the Node Address
2
1
0
9
8
3
4
5
6
7
2
1
0
9
8
3
4
5
6
7
Tens
Digit
Ones
Digit
Setting Description
Auto The adapter is set to the data rate used by other
network devices. Another device on the network
must be set to a data rate.
125 K
250 K
500 K
The adapter is set to the respective data rate.
PGM The adapter uses the setting of DN Rate Cfg (5) for
the data rate. Refer to chapter 4, Configuring the
DeviceNet Adapter.
Figure 3.2 – Setting the Data Rate
125K
250K
500K
PGM
AUTO
- DeviceNet Adapter 1
- DPI AC Drives 1
- Contents 3
- List of Figures 7
- List of Tables 9
- Introduction 11
- 1.2 Related Documentation 12
- Electric 13
- Getting Started 15
- 2.2 Required Equipment 16
- 2.3 Installation Checklist 17
- Step Action Refer to 18
- Installing the 19
- 3.5 Applying Power 23
- Configuring the 25
- SP600 Standard 31
- 4.5 Setting the Data Rate 32
- Peer-to-Peer 33
- 4.9 Setting a Fault Action 41
- 4.10 Resetting the Adapter 43
- 00010xxx 45
- 01234567 45
- 1=Enabled 45
- 0=Disabled 45
- Configuring the Scanner 47
- AC Drive 48
- Edit I/O 49
- Parameters 49
- 5.4) appears 49
- 5.3.1 Mapping the Input I/O 52
- 5.3.2 Mapping the Output I/O 53
- 5.4 Saving the Configuration 54
- Using I/O Messaging 55
- 6.4 Using Reference/Feedback 58
- 6.5 Using Datalinks 58
- Using Explicit 67
- Messaging 67
- ControlLogix Controller 68
- Using Explicit Messaging 69
- PLC or SLC Controller 70
- Word Description 71
- 7.4 Running Explicit Messages 73
- 7.5 ControlLogix Example 74
- 7.6 PLC-5 Example 76
- Ladder Logic Program 77
- 7.7 SLC Example 78
- Troubleshooting the 81
- and Network 81
- 8.1.1 DRIVE Status Indicator 82
- 8.1.2 MS Status Indicator 83
- 8.1.3 NET A Status Indicator 84
- 8.2 Adapter Diagnostic Items 85
- Technical 91
- Specifications 91
- 1DPI Port 94
- 2 DPI Data Rate 94
- 3 DN Addr Cfg 94
- 4 DN Addr Actual 94
- 5 DN Rate Cfg 95
- 6 DN Rate Actual 95
- 7 Ref/Fdbk Size 95
- 8 Datalink Size 95
- 9 Reset Module 96
- 10 Comm Flt Action 96
- 11 Idle Flt Action 97
- 12 DN Active Cfg 97
- 13 DPI I/O Config 98
- 14 DPI I/O Active 98
- 15 Flt Cfg Logic 99
- 16 Flt Cfg Ref 99
- Figure B.3 – M-S Input (25) 100
- 26 M-S Output 101
- 27 COS Status Mask 101
- 28 COS Fdbk Change 101
- 29 COS/Cyc Interval 102
- Peer A Input 102
- Peer B Input 102
- 32 Peer Cmd Mask 103
- 33 Peer Ref Adjust 103
- 34 Peer Flt Action 104
- 35 Peer Node to Inp 104
- 36 Peer Inp Timeout 105
- 37 Peer Inp Enable 105
- 38 Peer Inp Status 105
- 43 Peer Out Skip 107
- DeviceNet 109
- C.1 Identity Object 110
- Services 111
- C.2 Connection Object 112
- C.3 Register Object 114
- Instance Attributes 115
- C.4 Parameter Object 116
- C.5 Parameter Group Object 119
- C.6 PCCC Object 121
- C.7 DPI Device Object 123
- C.8 DPI Parameter Object 127
- DeviceNet Objects 129
- Descriptor Attributes 130
- Decimal Places 131
- Decimal Place) 131
- C.9 DPI Fault Object 137
- C.10 DPI Alarm Object 140
- C.11 DPI Time Object 142
- Logic Command/ 145
- Status Words 145
- Logic Status Word 146
- Logic Command/Status Words 147
- Master-Slave 149
- I/O Configuration 149
- Datalinks 152
- Datalinks (Continued) 153
- Datalinks (Continued) 155
- Datalinks 156
- Glossary-1 157
- Glossary-2 158
- Glossary-3 159
- Glossary-4 160
- Glossary-5 161
- Glossary-6 162
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation RECOMM-DNET DeviceNet Adapter for use with DPI AC
Ekwipunek Rockwell-automation RECOMM-485 RS485 DFI Communications Module Instrukcja Użytkownika
(68 strony)
(68 strony)
Ekwipunek Rockwell-automation FactoryTalk Historian SE 3.0 H2H Interface Install Instrukcja Użytkownika
(32 strony)
(32 strony)
Ekwipunek Rockwell-automation 20D PowerFlex 700S/700H Frame 10...14 Drives Maint Instrukcja Użytkownika
(10 strony)
(10 strony)
Ekwipunek Rockwell-automation T8292 Trusted Power Distribution Unit MCB 24V Instrukcja Użytkownika
(2 strony)
(2 strony)
Ekwipunek Rockwell-automation 1440-SPD02-01RB XM-220 Dual Speed Module Instrukcja Użytkownika
(12 strony)
(12 strony)
Ekwipunek Rockwell-automation MD60 Door-Mount NEMA 1 OIM Bezel Kit MDI Instrukcja Użytkownika
(6 strony)
(6 strony)
Ekwipunek Rockwell-automation Logix5000 Control Systems: Connect POINT I/O Modul Instrukcja Użytkownika
(62 strony)
(62 strony)
Ekwipunek Rockwell-automation 1203-USB USB Converter (Same as DRIVES-UM001) Out Instrukcja Użytkownika
(76 strony)
(76 strony)
Ekwipunek Rockwell-automation SP200 AC Drive, 1 2 Channel Analog, Preset Speed Instrukcja Użytkownika
(68 strony)
(68 strony)
Ekwipunek Rockwell-automation 440N Magnetically Operated Safety Switch Instrukcja Użytkownika
(4 strony)
(4 strony)
Ekwipunek Rockwell-automation T8017 Trusted Peer to Peer Communications Instrukcja Użytkownika
(46 strony)
(46 strony)
Ekwipunek Rockwell-automation GV3000/SE Operator Interface Module (OIM) User Gui Instrukcja Użytkownika
(112 strony)
(112 strony)
Ekwipunek Rockwell-automation FlexPak/WebPak 3000 DC Drive AutoMax Network Commu Instrukcja Użytkownika
(108 strony)
(108 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji