Rockwell-automation 21G PowerFlex 750-Series AC Drives Programming Man Instrukcja Użytkownika Strona 345
- Strona / 544
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Rockwell Automation Publication 750-PM001J-EN-P - October 2014 345
Troubleshooting Chapter 6
Embedded EtherNet/IP (Port
13) Events
The adapter has an event queue to record significant events that occur in the
operation of the adapter. When such an event occurs, an entry consisting of the
event’s numeric code and a timestamp is put into the event queue. You can view
the event queue using the PowerFlex 20-HIM-A6/-C6S HIM, DriveExplorer
software (version 6.01 or later), DriveExecutive software (version 5.01 or later) or
other clients using the DPI Fault object. For details on viewing and clearing
events using the HIM, see the PowerFlex 20-HIM-A6/-C6S HIM (Human
Interface Module) User Manual, publication 20HIM-UM001
.
Many events in the event queue occur under normal operation. If you encounter
unexpected communications problems, the events may help you or Rockwell
Automation personnel troubleshoot the problem. The following events may
appear in the event queue.
Table 15 - Adapter Events
Table 16 - DPI Events
Table 17 - Network Events
Code Event Description
13001 No Event Text displayed in an empty event queue entry.
13002 Device Power Up Power was applied to the adapter.
13003 Device Reset The adapter was reset.
13004 EEPROM CRC Error The EEPROM checksum/CRC is incorrect, which limits adapter functionality.
Default parameter values must be loaded to clear this condition.
13005 App Updated The adapter application firmware was flash updated.
13006 Boot Updated The adapter boot firmware was flash updated.
13007…
13024
Reserved –
Code Event Description
13025 DPI Manual Reset The adapter was reset.
13026…
13028
Reserved –
Code Event Description
13029 Net Link Up An network link was available for the adapter.
13030 Net Link Down The network link was removed from the adapter.
13031 Net Dup Address The adapter uses the same IP address as another device on the network.
13032 Net Comm Fault The adapter detected a communications fault on the network.
13033 Net Sent Reset The adapter received a reset from the network.
13034 Net IO Close An I/O connection from the network to the adapter was closed.
13035 Net Idle Fault The adapter received “idle” packets from the network.
13036 Net IO Open An I/O connection from the network to the adapter has been opened.
13037 Net IO Timeout An I/O connection from the network to the adapter has timed out.
13038 Net IO Size Err The adapter received an incorrectly sized I/O packet.
13039 PCCC IO Close The device sending PCCC Control messages to the adapter has set the PCCC
Control Timeout to zero.
13040 PCCC IO Open The adapter has begun receiving PCCC Control messages (the PCCC Control
Timeout was previously set to a non-zero value).
- Programming Manual 1
- Important User Information 2
- Summary of Changes 3
- New and Updated Information 3
- Table of Contents 5
- Chapter 5 6
- Embedded Feature and Option 6
- Chapter 6 6
- Overview 9
- Obtaining Manuals 10
- Product Certification 11
- Manual Conventions 11
- General Precautions 12
- Product Safety 13
- Class 1 LED Product 13
- Start Up 15
- Figure 1 - DPI Ports ➊ and ➋ 16
- Start-Up Menu 17
- Drive Status Indicators 18
- EtherNet/IP 19
- Parameter Organization 21
- About Parameters 22
- Parameter Access Level 23
- How Drive Parameters are 24
- Organized 24
- Motor Control 26
- Feedback and IO 26
- Drive Cong 27
- Protection 27
- Speed Control 28
- Torque Control 28
- Psn Offset 1 Sel 820 29
- Diagnostics 30
- Applications 30
- Not Applicable 39
- Inverter Common (Port 10) 40
- Inverter Common 40
- Inverter n 40
- Converter Common (Port 11) 41
- Converter Common 41
- Converter n 41
- Precharge Common (Port 11) 42
- Precharge Common 42
- Precharge n 42
- Embedded EtherNet/IP 43
- Embedded DeviceLogix 44
- How Option Module 45
- Parameters are Organized 45
- 22-Series I/O Modules 46
- 22-Series I/O 46
- Single Incremental 47
- Dual Incremental 47
- Universal Feedback 48
- Safe Speed Monitor 49
- Drive Port 0 Parameters 51
- Drive (Port 0) Monitor File 52
- Drive (Port 0) Motor Control 54
- Frequency 55
- Drive (Port 0) Cfg File 84
- (1) Frames 1…7 only 92
- 755 (8+) 105
- Drive (Port 0) Speed Control 111
- Freq (Hz) 127
- Attenuation 127
- Drive (Port 0) Position 133
- Control File 133
- (1) 755 drives only 134
- Drive (Port 0) 148
- Communication File 148
- (2) 753 drives only 159
- (1) 753 drives only 160
- (3) 755 drives only 166
- (2) 755 drives only 167
- Drive (Port 0) Applications 172
- PI Error 174
- Alt Slope 196
- -axis offset is enabled 200
- Spindle Orientation Offset 207
- Drive (Port 0) General 212
- Purpose Parameters 212
- Chapter 4 215
- Inverter (Port 10) Common 216
- Parameters 216
- Inverter n (Port 10) 218
- Converter (Port 11) Common 221
- Converter n (Port 11) 223
- Precharge (Port 11) Common 227
- Precharge n (Port 11) 229
- Embedded EtherNet/IP (Port 234
- 13) Parameters 234
- Communication 240
- Configurations 240
- Table 4 - Logic Command Word 241
- Table 5 - Logic Status Word 242
- Embedded DeviceLogix (Port 243
- 14) Parameters 243
- 11-Series I/O Module 246
- 22-Series I/O Module 256
- Single Incremental Encoder 267
- Module Parameters 267
- Dual Incremental Encoder 269
- Universal Feedback Module 274
- Encoder Output Z Offset 286
- Registration Latch 0 290
- Registration Latch N 290
- Option Bus I/O 290
- Safe Speed Monitor Module 292
- Troubleshooting 305
- Faults, Alarms and 306
- Configurable Conditions 306
- HIM Indication 309
- Manually Clearing Faults 309
- Power Layer Interface (PLI) 310
- Board 7-Segment Display 310
- System Resource Allocation 311
- Chapter 6 Troubleshooting 312
- Drive Fault and Alarm 313
- Descriptions 313
- IMPORTANT 324
- for descriptions 324
- 194 Port12 Checksum 272 326
- Alarms (Frame 8 and Larger) 328
- I2 Curr Offset 331
- Converter (Port 11) Faults 333
- Precharge (Port 11) Faults 338
- N-1 and Re-Rate Functions 341
- Use the Re-Rate Feature 342
- Troubleshooting Chapter 6 343
- 13) Events 345
- Safe Torque Off Fault 347
- I/O Faults and Alarms 347
- ATEX Faults 348
- Faults and Alarms 348
- Universal Feedback Faults 350
- Port Verification 357
- Common Symptoms and 357
- Corrective Actions 357
- Motor operation is unstable 358
- Problems adding a datalink 359
- PowerFlex 755 Lifting/ 360
- Torque Proving 360
- External Brake Resistor 360
- Technical Support Options 361
- Technical Support Wizards 362
- Appendix A 363
- Block Diagrams 363
- * Notes, Important: 364
- PowerFlex 753 365
- VF (V/Hz), SV Overview 366
- Speed/Posit Fdbk 367
- Speed Control – Reference (1) 369
- Speed Control – Reference (2) 370
- Speed Control – Reference (3) 371
- Flux Vector 371
- Speed Control – Reference (4) 372
- VF (V/Hz), SV 372
- Speed Control – Reference (5) 373
- Speed Control – Regulator 374
- Position Control – Reference 375
- Position Control – Regulator 376
- In Position Detect 377
- Position Control – Homing 378
- Torque Control – Overview 379
- Induction Motor (IM) 379
- Torque Control – Torque 382
- Torque Control – Current 383
- Process Control (1) 385
- Process Control (2) 386
- MOP Control 387
- Dig In Filt 388
- Buffer & 394
- Comparator 394
- PF753 Rev_10.a 394
- Control Logic 395
- Inverter Overload IT 396
- PowerFlex 755 400
- Position Watch 1 412
- Position Watch 2 412
- Reref Psn In 414
- Speed/Position 415
- Move Table 415
- Roll Psn Config 417
- SO Offset 418
- Position 419
- Induction Motor (IM) & 420
- Total Inertia 426
- PF755 Rev_10.a 435
- Friction Compensation 438
- Peak Detect 440
- Digital Switches 440
- Diagnostic Tools 440
- High Speed Trend Wizard 441
- Application Notes 443
- Application Notes Appendix B 445
- Crane Setup with Encoder 446
- Feedback 446
- Set Up the Drive 447
- Motor Tune Routines 447
- Static Tune 448
- Rotate Tune 449
- Inertia Tune 450
- Torque Prove 452
- Setup Complete 453
- Crane Setup - Encoderless 455
- 6. Set speed reference 460
- 8. Set speed loop tuning 460
- Pump Off Function 463
- Gather Motor and Pump Data 464
- Enter Motor Data 464
- Run Motor Tune Routine 465
- Enter Pump Data 466
- Store Pump Cycle Torque 467
- Appendix B Application Notes 468
- Fine Tuning 469
- Sleep Mode 469
- Pump Off Control Outlines 470
- Table 2 - Parameter List 474
- Predictive Maintenance with 475
- Example Code 477
- Using DeviceLogix 483
- Function Block Elements 485
- Bit and Analog I/O Points 486
- Analog Inputs 487
- Analog Outputs 487
- Data Types 488
- Using DeviceLogix Appendix C 489
- Drive Datalink Value 489
- Program Examples 490
- Parameter Configuration 491
- Functional Block Programming 492
- Example 3: Diverter Operation 495
- Example 4: Wet Well Operation 496
- Example logic requirements: 499
- Permanent Magnet Motors 501
- Appendix E 505
- Introduction 505
- Feedback Configuration 507
- Parameter / Instance 512
- Attribute Mapping 512
- 431 1AF Position Trim 514
- Motor Overload 515
- Enhanced Attributes 516
- Additional Resources 525
- Rockwell Automation Support 544
- Documentation Feedback 544
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 21G PowerFlex 750-Series AC Drives Programming Man
Ekwipunek Rockwell-automation 20-750-BNETIP BACnet/IP Option Module Instrukcja Użytkownika
(88 strony)
(88 strony)
Ekwipunek Rockwell-automation 20-750-PNET Profinet Single Port Option Module Instrukcja Użytkownika
(96 strony)
(96 strony)
Ekwipunek Rockwell-automation 140M-F Motor Protection Circuit Breaker Instrukcja Użytkownika
(2 strony)
(2 strony)
Ekwipunek Rockwell-automation 20-750-DNET PowerFlex DeviceNet Option Module Instrukcja Użytkownika
(144 strony)
(144 strony)
Ekwipunek Rockwell-automation 445L GuardShield Safe 4 and Safe 4 PAC Safety Ligh Instrukcja Użytkownika
(40 strony)
(40 strony)
Ekwipunek Rockwell-automation 440T Prosafe Switchgear Key Adaptors Instrukcja Użytkownika
(2 strony)
(2 strony)
Ekwipunek Rockwell-automation 160 Supplement-160-NX3 Chassis Mount Series C Instrukcja Użytkownika
(12 strony)
(12 strony)
Ekwipunek Rockwell-automation 140U Q, M frame CB Electronic RMS Trip Unit instal Instrukcja Użytkownika
(14 strony)
(14 strony)
Ekwipunek Rockwell-automation 140 Door-mounted Actuators for 140-CMN Instrukcja Użytkownika
(4 strony)
(4 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji