Rockwell-automation 6000 PowerFlex Medium Voltage Variable Frequency D Instrukcja Użytkownika Strona 15
- Strona / 98
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Rockwell Automation Publication 6000-IN007A-EN-P - October 2014 15
Chapter 2
Preparation and Inspection
Gather Required Tools and
Test Equipment
Hand Tools
• Metric wrenches and sockets
• To r q u e w r e n c h
• Assortment of screw drivers
• Wire stripper/cutter
Electrical Equipment
• High voltage gloves – 17 kV insulation rating (minimum)
• Anti-static strap
• Live-line tool (Hot stick)
• 5 kV Insulation Tester
Test Equipment
• 600V (1000V rating) digital multimeter with assorted clip leads
Computer Requirements and Software
• Laptop computer
• USB cable
• PLC program
• CCW software
Lockout and Tagout
SHOCK HAZARD: Servicing energized industrial control equipment can be
dangerous. Severe injury or death can result from electrical shock, burn, or
unintended actuation of control equipment. Hazardous voltages may exist in
the cabinet even with the input circuit breaker in the off position. Required
practice is to disconnect and lock out control equipment from power sources,
and confirm discharge of stored energy in capacitors. If it is necessary to work in
the vicinity of energized equipment, the safety related work practices outlined
in Electrical Safety requirements for Employee Work places must be followed.
Before attempting any work, verify the system has been locked out and tested
to have no potential.
- Commissioning Manual 1
- Important User Information 2
- Table of Contents 3
- Table 1 - Electrical Drawings 7
- General Precautions 9
- Additional Resources 9
- Introduction 11
- Documentation and 12
- Application Review 12
- Review Drive Application 13
- Chapter 1 Introduction 14
- Preparation and Inspection 15
- Inspect Drive Components 16
- Functional Assessment 17
- Interconnection Review 20
- Installation Review 21
- Power Cabling 22
- Drive Megger Check 23
- Figure 4 - Control Switches 25
- Figure 5 - Control Switches 25
- Figure 8 - Back of HMI 26
- Connect the Insulation Meter 27
- Final Steps before 29
- Equipment is Ready for 29
- Energization 29
- Commissioning 31
- Control System Check Setup 32
- Control System Check 35
- , press 36
- Access Setup Settings 37
- Set P Parameters 38
- Commissioning Chapter 3 39
- Chapter 3 Commissioning 40
- Increase Frequency by Step 41
- Simulate Warnings and Faults 45
- Verify E-Stop Functionality 50
- (Manual Bypass) 52
- Bypass Isolation Switches 54
- (Automatic Bypass) 55
- , and press 57
- Bypass Contactors 58
- Figure 17 - Status Indicators 61
- Table 9 - Drive to DCS 61
- Table 10 - 4-20 mA 61
- Restore P Parameter Settings 62
- Set Date and Time Zone 64
- No-load Test 67
- Configure P and T Parameters 68
- 0 ON -100 199.99 R&D 69
- (2) With Remote DCS only 70
- Parameters T11...T13 71
- Chapter 4 No-load Test 72
- Change Parameter T12: 73
- 3. Press to accept 73
- Close Input Circuit Breaker 75
- Check Cooling Fan Operation 75
- Operate Motor by HMI 76
- No-load Test Chapter 4 77
- Press to confirm 78
- Load Test of Drive System 80
- Torque Requirements 81
- Single Line Diagrams 83
- Appendix C 87
- Overview 87
- System Setting Functions 87
- Switch Control Sources 88
- Motor Parameter Setting 88
- Restore Factory Setting 89
- Speed Command Functions 90
- Frequency Amplitude Limit 91
- Frequency Skip 91
- Speed Reference Functions 92
- Analog Input 93
- Stop Mode 93
- Flying Start Function 93
- Restart the Drive 94
- Rockwell Automation Support 98
- Documentation Feedback 98
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 6000 PowerFlex Medium Voltage Variable Frequency D
Ekwipunek Rockwell-automation 2708-DH5B2L_DH5B4L Attended Workstation Instrukcja Użytkownika
(186 strony)
(186 strony)
Ekwipunek Rockwell-automation 2711PC-xxxx PanelView Plus 6 Compact Terminals Use Instrukcja Użytkownika
(162 strony)
(162 strony)
Ekwipunek Rockwell-automation 6181P_F VersaView 6181P Integrated Display Compute Instrukcja Użytkownika
(20 strony)
(20 strony)
Ekwipunek Rockwell-automation 2090-XBxxx Resistive Brake Module Installation Ins Instrukcja Użytkownika
(24 strony)
(24 strony)
Ekwipunek Rockwell-automation 2364F Regenerative DC Bus Supply Unit (RGU) Instrukcja Użytkownika
(222 strony)
(222 strony)
Ekwipunek Rockwell-automation 2755-SNx Adaptascan Bar Code Readers Instrukcja Użytkownika
(354 strony)
(354 strony)
Ekwipunek Rockwell-automation 2080 Micro800 Digital and Analog Plug-in Modules Instrukcja Użytkownika
(108 strony)
(108 strony)
Ekwipunek Rockwell-automation MV SMC Flex OEM Components - Fiber Optic Cables Instrukcja Użytkownika
(2 strony)
(2 strony)
Ekwipunek Rockwell-automation 2094-EN02D-M01-S0 Kinetix 6200 and Kinetix 6500 Sa Instrukcja Użytkownika
(42 strony)
(42 strony)
Ekwipunek Rockwell-automation 2706-P22R InView Panel Mount Message Display Insta Instrukcja Użytkownika
(52 strony)
(52 strony)
Ekwipunek Rockwell-automation 57C409 2 Channel Analog Input Module Instrukcja Użytkownika
(44 strony)
(44 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.142 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji