Rockwell-automation 6000 PowerFlex Medium Voltage Variable Frequency D Instrukcja Użytkownika Strona 68
- Strona / 98
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
68 Rockwell Automation Publication 6000-IN007A-EN-P - October 2014
Chapter 4 No-load Test
Energize Drive Control Circuit
The “Energize Control Circuit” process is already described on page 32. For the
“Energize Drive Control Circuit” procedure, repeat the process in the same
sequence, without the requirements of taking voltage measurements.
1. Close circuit breaker Q1.
2. Start UPS. Press and hold the ON button for approximately 3 seconds.
3. Close circuit breakers Q2, Q3, Q5, and Q6 in the LV Control Panel.
4. Close circuit breakers Q4 and Q7 in the Isolation Transformer Cabinet LV
Panel.
Configure P and T Parameters
Set the P parameters and T parameters as shown in Table 12.
This table outlines the specific parameters that must be checked and/or
modified. Parameters that must be modified are outlined in the Instruction
column. All other parameters listed must be verified. For special functions or
actions which are not listed here, but are commonly performed while
commissioning a drive, see Special Function Parameter Settings
on page 87.
TIP
See Set P Parameters to Enable Testing on page 37 for information on how to
access and change parameters.
Table 12 - Setup and R&D Parameters
P
Parameter
Description Default Modify
Root
(1)
Min.
Value
Max.
Value
Login
Level
Instruction
P004 Command Source
0: Communication Port
1: Other Sources
0OFF01Setup
P007 Number Of Power Cells Per Phase 9 ON 0 9 Setup Set to 0 for Control System Check. Afterwards, set to actual value
according to Electrical Drawings
P008 Motor Rotation Direction Under Local Control
1: Forward
0: Reverse
1OFF01Setup
P009 Motor Rotation Direction Command
Selection
0: Local
1: DCS
0OFF01Setup
P024 Stop Method
0: Ramp Down
1: Coast Stop
0ON01R&D
P040 Safe Start Condition
0: Zero Frequency Command Required
1: Frequency Command Allowed
1OFF01Setup
P089 Skip Frequency Enable
0: Disable
1: Enable
0ON01R&D
P090 Skip Frequency 1 Lower Limit 0 ON 0 75 R&D
- Commissioning Manual 1
- Important User Information 2
- Table of Contents 3
- Table 1 - Electrical Drawings 7
- General Precautions 9
- Additional Resources 9
- Introduction 11
- Documentation and 12
- Application Review 12
- Review Drive Application 13
- Chapter 1 Introduction 14
- Preparation and Inspection 15
- Inspect Drive Components 16
- Functional Assessment 17
- Interconnection Review 20
- Installation Review 21
- Power Cabling 22
- Drive Megger Check 23
- Figure 4 - Control Switches 25
- Figure 5 - Control Switches 25
- Figure 8 - Back of HMI 26
- Connect the Insulation Meter 27
- Final Steps before 29
- Equipment is Ready for 29
- Energization 29
- Commissioning 31
- Control System Check Setup 32
- Control System Check 35
- , press 36
- Access Setup Settings 37
- Set P Parameters 38
- Commissioning Chapter 3 39
- Chapter 3 Commissioning 40
- Increase Frequency by Step 41
- Simulate Warnings and Faults 45
- Verify E-Stop Functionality 50
- (Manual Bypass) 52
- Bypass Isolation Switches 54
- (Automatic Bypass) 55
- , and press 57
- Bypass Contactors 58
- Figure 17 - Status Indicators 61
- Table 9 - Drive to DCS 61
- Table 10 - 4-20 mA 61
- Restore P Parameter Settings 62
- Set Date and Time Zone 64
- No-load Test 67
- Configure P and T Parameters 68
- 0 ON -100 199.99 R&D 69
- (2) With Remote DCS only 70
- Parameters T11...T13 71
- Chapter 4 No-load Test 72
- Change Parameter T12: 73
- 3. Press to accept 73
- Close Input Circuit Breaker 75
- Check Cooling Fan Operation 75
- Operate Motor by HMI 76
- No-load Test Chapter 4 77
- Press to confirm 78
- Load Test of Drive System 80
- Torque Requirements 81
- Single Line Diagrams 83
- Appendix C 87
- Overview 87
- System Setting Functions 87
- Switch Control Sources 88
- Motor Parameter Setting 88
- Restore Factory Setting 89
- Speed Command Functions 90
- Frequency Amplitude Limit 91
- Frequency Skip 91
- Speed Reference Functions 92
- Analog Input 93
- Stop Mode 93
- Flying Start Function 93
- Restart the Drive 94
- Rockwell Automation Support 98
- Documentation Feedback 98
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 6000 PowerFlex Medium Voltage Variable Frequency D
Ekwipunek Rockwell-automation 2708-DH5B2L_DH5B4L Attended Workstation Instrukcja Użytkownika
(186 strony)
(186 strony)
Ekwipunek Rockwell-automation 2711PC-xxxx PanelView Plus 6 Compact Terminals Use Instrukcja Użytkownika
(162 strony)
(162 strony)
Ekwipunek Rockwell-automation 6181P_F VersaView 6181P Integrated Display Compute Instrukcja Użytkownika
(20 strony)
(20 strony)
Ekwipunek Rockwell-automation 2090-XBxxx Resistive Brake Module Installation Ins Instrukcja Użytkownika
(24 strony)
(24 strony)
Ekwipunek Rockwell-automation 2364F Regenerative DC Bus Supply Unit (RGU) Instrukcja Użytkownika
(222 strony)
(222 strony)
Ekwipunek Rockwell-automation 2755-SNx Adaptascan Bar Code Readers Instrukcja Użytkownika
(354 strony)
(354 strony)
Ekwipunek Rockwell-automation 2080 Micro800 Digital and Analog Plug-in Modules Instrukcja Użytkownika
(108 strony)
(108 strony)
Ekwipunek Rockwell-automation MV SMC Flex OEM Components - Fiber Optic Cables Instrukcja Użytkownika
(2 strony)
(2 strony)
Ekwipunek Rockwell-automation 2094-EN02D-M01-S0 Kinetix 6200 and Kinetix 6500 Sa Instrukcja Użytkownika
(42 strony)
(42 strony)
Ekwipunek Rockwell-automation 2706-P22R InView Panel Mount Message Display Insta Instrukcja Użytkownika
(52 strony)
(52 strony)
Ekwipunek Rockwell-automation 57C409 2 Channel Analog Input Module Instrukcja Użytkownika
(44 strony)
(44 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.090 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji