Rockwell-automation IASIMP Computer Numerical Control (CNC) Machining Instrukcja Użytkownika Strona 25
- Strona / 278
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Rockwell Automation Publication IASIMP-QS034A-EN-P - October 2012 25
Architecture and Hardware Selection Chapter 1
2. Select the System I/O.
a. Use the tabs near the bottom of the
spreadsheet to navigate to and select
the IOetc tab, for I/O selection.
The IOetc tab is displayed.
b. Use the cells in the spreadsheet to
navigate to and select the
appropriate I/O modules, based on
your specific application
requirements.
The 35i-B selections are displayed.
c. Use the cells in the spreadsheet to
navigate to and select the
appropriate I/O and options.
When all options are selected the
cell at the bottom of the tab (U268)
will display either a TRUE
OVERALL or FALSE OVERALL
status. Make the appropriate
corrections until the status reads
TRUE OVERALL.
The I/O configuration is now complete.
TIP
The Status is FALSE until the
I/O selection has been satisfied
in the next step.
- Accelerator Toolkit 1
- Important User Information 2
- Chapter 7 3
- Where to Start 4
- Chapter 4 6
- GuardLogix Configuration 6
- Chapter 5 6
- Appendix D 9
- Configuration 9
- Table of Contents 10
- Introduction 11
- Conventions 12
- Required Software 12
- Additional Resources 13
- FANUC CNC Express Software 19
- System Layout and Wiring 29
- • The 07_PLC_1791DS_IB16 and 32
- Project Drawings folder 33
- Edit FANUC CNC Drawing Set 34
- Edit CNC Power Drawings 35
- • 16_CNC_Ethernet_Switch 41
- • 18_CNC_Cable_Connections 41
- CNC Subpanel Layout Drawing 43
- CNC Enclosure Layout Drawing 43
- Drive Power Example 44
- Drive I/O Example 44
- System Layout Example 44
- FANUC CNC Configuration 47
- Parameter Write Enable 49
- High Speed Ethernet Option 51
- Configure Ethernet Module 53
- Create a New Project File 56
- 5. Select the model 58
- USB External Device 63
- EtherNet/IP Settings 64
- Logic Configuration 68
- P0001 (OP Panel Path 1) 71
- P0005 (Machine Sequence) 71
- P0010 (Window Functions) 72
- P0023 (Alarm Routine) 72
- Device Logic Modules 73
- 4. Click to save your FANUC 76
- LADDER III application file 76
- Figure 8 - Logic Modules 81
- Order and Run the DMAT Wizard 84
- Save the Project File 90
- 9. Click OK 94
- FANUC CNC AOP Configuration 95
- Add and Configure FANUC CNC 96
- The Import Configuration 101
- Import 105
- Machining Example 109
- Drill CNC Example 109
- Gantry Y Axis Drive Example 110
- Machine CNC Example 110
- Gantry X Axis Drive Example 110
- • Drill CNC 111
- • Machining CNC 111
- • Gantry X Axis Drive 111
- • Gantry Y Axis Drive 111
- IMPORTANT 113
- _ModuleNameXX tag 116
- Logic Placeholder 121
- Safety Logic Integration 137
- GuardLogix Safety Logic 138
- Safety Faceplate Logic 144
- Before You Begin 149
- What You Need 149
- Follow These Steps 150
- Delete Unused Displays 154
- Delete Unused Parameter Files 155
- Configure Parameter Files 156
- Parameters 157
- Comments 157
- Chapter 6 158
- • SafeIOAlarmTrigger 160
- • ModuleAlarmTrigger 160
- • CNCAlarmTrigger 160
- • CIPMotionAlarmTrigger 160
- Add Parameter Files 165
- Parameters folder 166
- Import Alarm Setup File 171
- • SaveIOAlarmTrigger 173
- Import and Edit Alarm Tags 174
- Goto Display Buttons 189
- CellGuard1 193
- System Commissioning 195
- Download Applications 197
- Terminal 202
- Commissioning Devices 205
- Verify Network Communication 206
- 1756-EN2TR 207
- EtherNet/IP 207
- • If there is an active 211
- Clearing Faults 212
- Operator (manual) Control 212
- Program (automatic) Control 213
- System Application Guide 215
- Machine Startup Faceplate 217
- Machine Control 219
- Program/Operator Mode 219
- CNC Faceplate 221
- CNC Status Views 222
- CNC Control Views 222
- Fault Indication View 223
- Fault Diagnostic Views 224
- Configuration View 225
- Guard I/O Safety Faceplates 226
- Logic Program Overview 229
- Module Routine Overview 231
- Machine Module 234
- Machine Control Module Tags 236
- Application Modules 240
- Device Modules 241
- Logic Module Customization 243
- • Mode = UDT_MachMode 244
- • Command = UDT_MachCmd 244
- • State = UDT_MachState 244
- (2) Refer to Chapter 5 246
- Module Fault Customization 249
- Appendix 255
- Add Optional Faceplate Views 258
- Verify Your IP Address 262
- Load the Controller Firmware 265
- Assign IP Addresses 267
- Numerics 271
- Rockwell Automation Support 278
- Documentation Feedback 278
Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation IASIMP Computer Numerical Control (CNC) Machining
(4 strony)
Ekwipunek Rockwell-automation SP120 ACDrive 115VAC, 1Ph, 230VAC, 1Ph/3Ph, 1/4-5. Instrukcja Użytkownika
(210 strony)
(210 strony)
Ekwipunek Rockwell-automation MDO16GNS 16-Channel Digital Output Module 48Vdc Instrukcja Użytkownika
(16 strony)
(16 strony)
Ekwipunek Rockwell-automation T8451 Trusted Industrial Control System Instrukcja Użytkownika
(2 strony)
(2 strony)
Ekwipunek Rockwell-automation T8480 Trusted TMR Analogue Output Module Instrukcja Użytkownika
(2 strony)
(2 strony)
Ekwipunek Rockwell-automation 1440-REX03-04RG XM-442 Voted EODS Relay Module Instrukcja Użytkownika
(12 strony)
(12 strony)
Ekwipunek Rockwell-automation T7454 ICS Regent+Plus AC Isolated Digital Output M Instrukcja Użytkownika
(13 strony)
(13 strony)
Ekwipunek Rockwell-automation TDI16EIA 16-Channel Digital Input Termination Card Instrukcja Użytkownika
(11 strony)
(11 strony)
Ekwipunek Rockwell-automation 2097-V3xPRx-LM Kinetix 300 and Kinetix 350 Drive S Instrukcja Użytkownika
(84 strony)
(84 strony)
Ekwipunek Rockwell-automation WebPak 3000 DC Drives Hardware Reference, Install Instrukcja Użytkownika
(92 strony)
(92 strony)
Ekwipunek Rockwell-automation T8423 Trusted TMR 35 - 120 Vdc Digital Input Modul Instrukcja Użytkownika
(33 strony)
(33 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji