Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra Instrukcja Użytkownika Pobierz pdf (Strona 788)

Error and System Messages

Appendix B

B-34

Message Description

POCKET IS PART OF CUSTOM TOOL Anattemptwasmadeto assign a toolto a tool pocketthatis already usedbya customtool.

Customtoolsare assigned totoolpocketsthatareshown with an XXXXnexttothepocket

numberon the randomtooltable.

POCKET MILLING SHAPE IS INV ALID Aparameteris missingin the G88 programmingblock.

POINT ALREADY EXISTS T he point thatyou are trying toenter isalreadyin the axiscalibrationtable.

PORTBISBUSY Thismessageappearswhenyoupress {SYSTEM SUPORT}, {MONITOR}, or {SERIAL I/O} and

portB is busy.

PORT IS BUSY - REQUEST DENIED Anattemptwas madetooutputor input information to orfroma serialcommunicationsportthat

isalreadybeing used by someother deviceor is selectedas the portthatan active programis

comingfrom.

PREVIOUS ABORT COMMAND NOT COMPLETE This messageis displayed when thecommunications“abort” key isentered beforethe lastabort

requested hascompleted.

PROBE/CONTROLLING AXISCARD DIFFERENT Both the adaptivedepth probe and theadaptive depthprobe controllingaxis (typicallythe axis

thatpositionsthe probe)mustbe attached to thesame servocard. You mustre-AMPyour

systemand re-arrange yourservowiring so thatthe adaptivedepthprobe and i t’scorrespondi ng

servoareonthesameservocard.

PROBE CYCLES CALCULATION ERROR The servomodule was unable tocomputetheprobe positionwhen the probe isfired. Make

sure thatall measurement pointsare withintheprogrammed range enteredfortheprobe cycle.

Lowerthefeedrateduring the probingoperation and tryagain.

PROBE CYCLES PROGRAMMING ERROR Either not enough or toomany axes are programmed in a probing cycle block.

PROBEERROR Aprobing cycle has reached the outerlimits ofthetolerance band withoutfiring the probe,orthe

probehasfired beforeentering thetolerance band.

PROBE IN USE BY OTHER PROCESS On a dual processing control onlyone probing functionis allowed at anyonetime. Probing can

notbe performedby both processes simultaneously. You mustwaitforprobingto completein

one processbeforeprobing in the otherprocess.

PROBE IS ARMED, CAN’T ADJUST SERVOS With theprobearmed througha probing operation,until theprobefiresorthe probe is disarmed,

otheronline AMPservo parameterslike torque,feedforward percentage,gain, etc., are not

allowed tobe changed.

PROBETRIPDURING DECEL An adaptivedepthprobe tripoccurredafter the programblock reachedendpoint. The tripwas

madewhilethecontrolwas waiting forthe followingerror tocollapse afterinterpolation is

complete. Avoid thiserrorbyreducing axisspeed(thusreducingfollowing error)or by moving

theadaptive depthblock endpointfurtherinto thepart.

PROCESSSWITCH NOT CURRENTLYALLOWED On a dual-processing system,youcannotswitch processes while in graphicsorin digitize.

PROGRAM ACTIVE An attempt hasbeenmadeto delete orperformsome otheroperation toa program thatwas

activatedfor automatic execution. The programmustbe deactivatedusing the {CANCEL

PRGRAM} softkey .

PROGRAM ACTIVE IN ANOTHER PROCESS This dual lathe errorappears when one processattemptsto open a filefor edit,deletion,etc.,

while thatfileisactiveinanotherprocess.

PROGRAM BEING EDITED Anattempthasbeenmadeto copy,verify,or performsomeotheroperationon a program thatis

stillin the editmode. Itis necessary to pressthe {EXIT EDITOR} softkey fromthe editmenu to

properlyend an editing operation.

PROGRAMBLOCKTOOLONG Morethan 128 characters were enteredinto a singleblock.

PROGRAMCURRENTLYINUSE A subprogramor paramacroprogram wascalledthatiscurrentlybeing used to performsome

otheroperation(such aseditingor copying). Typically,this messageis theresultofattempting

toedit a programthatwasnotproperlyclosed. Aprogramremainsin the editmodeuntil the

{EXIT EDITOR}softkeyis pressedfromtheprogrameditmenu.

PROGRAMNAMETOOLONG An attemptwas madetocreateaprogramwithaprogramnamelongerthan8 alphanumeric

characters. Ifalarge,descriptive programname is desired,a commentmaybe added tothe

rightof theprogramname using the{PRGRAMCOMENT}feature.

1 2 ... 783 784 785 786 787 788 789 790 791 792 793 ... 819 820

Komentarze do niniejszej Instrukcji

Brak uwag

Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra Instrukcja Użytkownika Strona 788

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Ekwipunek Rockwell-automation 8520-GUM 9/Series CNC Grinder Operation and Progra